Jump to content
SAU Community

Recommended Posts

if im not in a hurry i normally wait for the oil pressure to hit normal. most morning id run out side start the car up set the turbo timer to 10 mins then arm the alarm and run back in lol by the time im dressed shes nice and warm and good to go. if im in a hurry id get it wait for 1 min start driving but wont hit boost and like others say keep revs below 3000rpm

idle ur car is bad for ur engine? cant be??

Idling is not bad for your motor. Running cold is.

So (within reason) the quicker it gets up to its correct operating temperature the less wear you will get.

So sitting in the driveway for 5 minutes whilst the thing sits there running cold is bad for the motor & will undoubtedly annoy the fk out of your neighbours.

i agree, on a cold morning just letting the car sit and idle till it warms up can take much much longer than if you just drive it slow, especially if the car doesn't get kept in a closed off garage.

and also the time it takes depends on your thermostat. if your thermostat is stuffed and not closing properly, letting it idle up to temp could take an hour on a very cold morning, which isn't good for the motor at all.

when i drive to work in the morning, by the time i have been sitting at intersections, etc, the car is usually up to temp in less than 1km, and that would be no more than 3 or 4 mins. although my skyline used to take a touch longer to come up to temp.

Yeah it's a trade off between running your car cold on idle for 5mins, or driving your car cold under 3000rpm for 2mins...

Personally i drive below 3000rpm to warm mine up... and never put my foot into it until the oil temp has got above 70.

yep, very bad idea to let the car sit at cold idling for 5 mins. apart from being bad for the engine it also means that you are not getting any temp into your gearbox, diffs, brakes or clutch. so when you do finally set off your engine will be up to temp but nothing else will be.

imo the best idea is start car. take your time getting comfy etc and you should be edging out of the garage about 30 seconds after you started the car. I am the same as ferni in that I just drive it normally along (minimal boost, revs under about 3,000) until the oil temp passes 70. then you can have some fun if you want, but hold off on any real 'fangining' until oil temp is 75+. :thumbsup:

remote start while i'm brushing my teeth...

when i get in a minute later the climate control is just right, dvd is playing, cars starting to get warm and the back windscreen is demisted.

/bling

It's even more important to warm the car a little if you're running forged pistons. I usually finish breakfast, start car, brush teeth then drive away below 3k with gentle acceleration.

I read somewhere that 90% of engine wear occurs in the first 11 mins, how true this is im not sure. But judging by how much longer oil temp takes to increase compared to water temp its certainly increased my level of engine sympathy from now on...

Driving at below 300rpm may be fine for a gtst, because it wont be on boost, but for a gtr (a standard one that is) it is on boost. My car has forged pistons and I find that it wont rev really well because of co;d start requirements anyway. What I do is let it sit there for a couple of minutes till say the water temp guage reads at about 1/4 then begin to drive it, gently of course until fully warmed up. The oil temp guage in the centre, i think this is for the gearbox, will take about three times as long to warm up as your engine, but still be carefull with it until it reaches about 85 degrees.

Hope this helped.

how much it comes on boost depends on how much accelerator you give it. my gts-t would be at 13psi by less than 3000rpm if i booted it, but i could keep it pretty much off boost and drive along at 4000rpm. the more you plant your foot the more boost you are going to give it. not just the rpm.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...