Jump to content
SAU Community

Recommended Posts

if im not in a hurry i normally wait for the oil pressure to hit normal. most morning id run out side start the car up set the turbo timer to 10 mins then arm the alarm and run back in lol by the time im dressed shes nice and warm and good to go. if im in a hurry id get it wait for 1 min start driving but wont hit boost and like others say keep revs below 3000rpm

idle ur car is bad for ur engine? cant be??

Idling is not bad for your motor. Running cold is.

So (within reason) the quicker it gets up to its correct operating temperature the less wear you will get.

So sitting in the driveway for 5 minutes whilst the thing sits there running cold is bad for the motor & will undoubtedly annoy the fk out of your neighbours.

i agree, on a cold morning just letting the car sit and idle till it warms up can take much much longer than if you just drive it slow, especially if the car doesn't get kept in a closed off garage.

and also the time it takes depends on your thermostat. if your thermostat is stuffed and not closing properly, letting it idle up to temp could take an hour on a very cold morning, which isn't good for the motor at all.

when i drive to work in the morning, by the time i have been sitting at intersections, etc, the car is usually up to temp in less than 1km, and that would be no more than 3 or 4 mins. although my skyline used to take a touch longer to come up to temp.

Yeah it's a trade off between running your car cold on idle for 5mins, or driving your car cold under 3000rpm for 2mins...

Personally i drive below 3000rpm to warm mine up... and never put my foot into it until the oil temp has got above 70.

yep, very bad idea to let the car sit at cold idling for 5 mins. apart from being bad for the engine it also means that you are not getting any temp into your gearbox, diffs, brakes or clutch. so when you do finally set off your engine will be up to temp but nothing else will be.

imo the best idea is start car. take your time getting comfy etc and you should be edging out of the garage about 30 seconds after you started the car. I am the same as ferni in that I just drive it normally along (minimal boost, revs under about 3,000) until the oil temp passes 70. then you can have some fun if you want, but hold off on any real 'fangining' until oil temp is 75+. :thumbsup:

remote start while i'm brushing my teeth...

when i get in a minute later the climate control is just right, dvd is playing, cars starting to get warm and the back windscreen is demisted.

/bling

It's even more important to warm the car a little if you're running forged pistons. I usually finish breakfast, start car, brush teeth then drive away below 3k with gentle acceleration.

I read somewhere that 90% of engine wear occurs in the first 11 mins, how true this is im not sure. But judging by how much longer oil temp takes to increase compared to water temp its certainly increased my level of engine sympathy from now on...

Driving at below 300rpm may be fine for a gtst, because it wont be on boost, but for a gtr (a standard one that is) it is on boost. My car has forged pistons and I find that it wont rev really well because of co;d start requirements anyway. What I do is let it sit there for a couple of minutes till say the water temp guage reads at about 1/4 then begin to drive it, gently of course until fully warmed up. The oil temp guage in the centre, i think this is for the gearbox, will take about three times as long to warm up as your engine, but still be carefull with it until it reaches about 85 degrees.

Hope this helped.

how much it comes on boost depends on how much accelerator you give it. my gts-t would be at 13psi by less than 3000rpm if i booted it, but i could keep it pretty much off boost and drive along at 4000rpm. the more you plant your foot the more boost you are going to give it. not just the rpm.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...