Jump to content
SAU Community

Whats Better

GT-R FREAk
 Share

Recommended Posts

lingeringsoul Grand Master

lingeringsoul

Posted
Posted

well...when you are rich, you get the most expensive one out of the list. You pay the most expensive brand of turbo and mods. "which is better in price and performance" should not be in your vocabulary. "I'll take which ever gives me the best performance" would be the only sentence you need when you are rich.

Link to comment
https://www.sau.com.au/forums/topic/209971-whats-better/#findComment-3712888
Share on other sites
Greekos Proficient

Greekos

Posted
Posted
hi im amjad and i want to buy a skyline when im rich which one is better in Price and Performance and how much they approxmatly cost in AUS.

GT-R r34 V-spec I

or

GT-R r34 V-spec II

or

GT-R r34 V-spec II Nur

even better why wait till your rich, why not buy one of these R/C GT-R r34 V-spec II Nur :whistling:

4533.jpg

Link to comment
https://www.sau.com.au/forums/topic/209971-whats-better/#findComment-3713085
Share on other sites
1C3B3RG Rising Star

1C3B3RG

Posted
Posted
hi im amjad and i want to buy a skyline when im rich which one is better in Price and Performance and how much they approxmatly cost in AUS.

GT-R r34 V-spec I

or

GT-R r34 V-spec II

or

GT-R r34 V-spec II Nur

Hey dude, these guys are just havin fun. You obviously have access to the internet. Do the research yourself. The link below will start you on your journey, maybe motivate you when you become rich. Also, when you buy a Skyline you will stop being rich very soon. It is an expensive business running one. It is however very rewarding. Good luck.

http://www.j-spec.com.au/

Link to comment
https://www.sau.com.au/forums/topic/209971-whats-better/#findComment-3714664
Share on other sites
(OO)SKYLINE(OO) Grand Master

(OO)SKYLINE(OO)

Posted
Posted
hi im amjad and i want to buy a skyline when im rich which one is better in Price and Performance and how much they approxmatly cost in AUS.

GT-R r34 V-spec I

or

GT-R r34 V-spec II

or

GT-R r34 V-spec II Nur

GT-R R34 V-Spec I

The V-spec model also had firmer suspension, lower ground clearance, a plastic front air diffuser (covering the underside of the engine) and a rear carbon fiber air diffuser, designed to keep air flowing smoothly under the car.

GT-R R34 V-Spec II

The V-Spec II has increased stiffness in the suspension (even stiffer than the original V-spec). It also comes equipped with a carbon fiber hood, which is lighter than the aluminum that all other GT-R hoods are made from. Also different on the V-Spec II is the darker color of the center console in the interior. The seats were also made with black cloth, rather than the gray cloth used on other R34 GT-R models. From this point, the standard trim level GT-R also received the new black seats.

GT-R R34 V-Spec II Nur

The Nür was named after the famous German Nürburgring racetrack, where the Skyline was developed. The Nür model featured an improved RB26DETT based on the N1 racing engine, used by Nismo in Motorsports. The V-spec II Nür is based on the regular V-spec II model, and the M-spec Nür was based on the regular M-spec model. Other than the addition of the Nür engine, the Nür models also included a different color of stitching on the interior trim, as well as a speedometer reading up to 300 km/h (186 mph).

- http://en.wikipedia.org/wiki/Skyline_gtr

Link to comment
https://www.sau.com.au/forums/topic/209971-whats-better/#findComment-3715762
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...