Jump to content
SAU Community

Recommended Posts

yeah taking muffler out. got it back :P just a quik job in and out...

oh yeah ash advice next time you need a fuel pump changed... dont fill up your tank ! haha

lol i realised that after i filled it up lol. Did they start working on it then or did they just see the full gauge? Oh and was that you with the fluro top?

was it pound road ? or sth gippy just before the round about ? cause i remeber a white 33 come up next to me, i looked but they didnt seem to interested so i assumed just another skyline driver.

spotted AP .. LEANBAC... in noble park parked outside the tafe thingy ... was gonna put a card just to make you look over your shoulder but had none on me!

white r34 at re customs before while i was there, gold piping.

and an r33 with on big thick blue line down the middle of the car on chandler road 7.30pm thats all for today :P

I was in a new euro, not moby, my whale...and I would have waved thats for sure.

saw wayne on 3 occasions today this morning on narre cranny rd and then on ernest wanke rd this arvi while i had a L plater drive my car and then at berwick maccas where we stopped for bout 30 min and had a chat and then we saw a very very nice one of the cleanest r33's i ever seen, gave him a spotted card and gave him the run down of wat sau is and wat its about. he seemed pretty keen.

At Cue Room last night; saw a really nice r34 gtt in white with mega bodykit.

a black r33 gts-t with gt stripes on bonnet/roof/bootlid etc; had personalised plates was parked on settlement rd. Anyone on here?

Anyone else here go to cue room or bar8?

saw a yellow r34 with sau stickers goin over the freeway on narre north rd at bout lunch time then saw a blue r34 gt at waverley gardens and then a marone 33 doing a uturn at police and jacksons rd and going into shell servo

Was working down in the Nissan Engineering workshop yesterday and spotted 3 new GTR's. Had a good look at the first pilot vehicle for the Australian delievered version. :) This is the Grey coloured one that everyone keeps seeing around Dandenong. I also had a grand tour of some of the specialist equipment thats required for GTR at the dealerships for servicing, i must say, there is some serious equipment for this car, and there is a special deisgned hoist purely for the GTR that the dealerships require for their servicing.

Also had a look at the new 370Z, both nice looking pieces of machinary

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...