Jump to content
SAU Community

Recommended Posts

yeah taking muffler out. got it back :P just a quik job in and out...

oh yeah ash advice next time you need a fuel pump changed... dont fill up your tank ! haha

lol i realised that after i filled it up lol. Did they start working on it then or did they just see the full gauge? Oh and was that you with the fluro top?

was it pound road ? or sth gippy just before the round about ? cause i remeber a white 33 come up next to me, i looked but they didnt seem to interested so i assumed just another skyline driver.

spotted AP .. LEANBAC... in noble park parked outside the tafe thingy ... was gonna put a card just to make you look over your shoulder but had none on me!

white r34 at re customs before while i was there, gold piping.

and an r33 with on big thick blue line down the middle of the car on chandler road 7.30pm thats all for today :P

I was in a new euro, not moby, my whale...and I would have waved thats for sure.

saw wayne on 3 occasions today this morning on narre cranny rd and then on ernest wanke rd this arvi while i had a L plater drive my car and then at berwick maccas where we stopped for bout 30 min and had a chat and then we saw a very very nice one of the cleanest r33's i ever seen, gave him a spotted card and gave him the run down of wat sau is and wat its about. he seemed pretty keen.

At Cue Room last night; saw a really nice r34 gtt in white with mega bodykit.

a black r33 gts-t with gt stripes on bonnet/roof/bootlid etc; had personalised plates was parked on settlement rd. Anyone on here?

Anyone else here go to cue room or bar8?

saw a yellow r34 with sau stickers goin over the freeway on narre north rd at bout lunch time then saw a blue r34 gt at waverley gardens and then a marone 33 doing a uturn at police and jacksons rd and going into shell servo

Was working down in the Nissan Engineering workshop yesterday and spotted 3 new GTR's. Had a good look at the first pilot vehicle for the Australian delievered version. :) This is the Grey coloured one that everyone keeps seeing around Dandenong. I also had a grand tour of some of the specialist equipment thats required for GTR at the dealerships for servicing, i must say, there is some serious equipment for this car, and there is a special deisgned hoist purely for the GTR that the dealerships require for their servicing.

Also had a look at the new 370Z, both nice looking pieces of machinary

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...