Jump to content
SAU Community

Recommended Posts

What time did you see the r32? Could have been me? I was on Warigal road crossing princes hwy?

Think it was around 11:00pm ish, not later than midnight. Not sure if it had custom plates, sure it didn't, you wouldn't of seen me anyway as I was always a few cars behind.

Saw a red M35 Stagea turning onto Hallam-Belgrave Rd from Narre North Rd around 4:30pm tonight, nice. Also the same silver V35 coupe down Harkaway Rd minutes later, gave you a wave.

He said a nice R32 Pat :P

:(

Think it was around 11:00pm ish, not later than midnight. Not sure if it had custom plates, sure it didn't, you wouldn't of seen me anyway as I was always a few cars behind.

Saw a red M35 Stagea turning onto Hallam-Belgrave Rd from Narre North Rd around 4:30pm tonight, nice. Also the same silver V35 coupe down Harkaway Rd minutes later, gave you a wave.

wasnt me then! carry on.

ha thats my gym too

i think we should go to gym together....

i will not be there today, its my rest day, but will be there tomorrow after 5.30 PM :)

if any of you see me, come and approach...ill be wearing a red and black stripe singlet and blue knee length shorts :)

Edited by lav

hahahaha....where did you park???i was looking for ur car :)

i was there about 6.30PM...i parked at the car park this time, there were no parking at the council....

i park in the actual carpark and not the library LOL i got there around 6:30 and left about 7:30ish when i saw your car..

i think we should go to gym together....

i will not be there today, its my rest day, but will be there tomorrow after 5.30 PM :)

if any of you see me, come and approach...ill be wearing a red and black stripe singlet and blue knee length shorts :)

will give you a shout bud! my missus comes with me too i just cbf going on weekends, so theyre my rest days lol

i park in the actual carpark and not the library LOL i got there around 6:30 and left about 7:30ish when i saw your car..

will give you a shout bud! my missus comes with me too i just cbf going on weekends, so theyre my rest days lol

sounds good mate, will see you tomorrow around the same time :)

i also have rest day on sat or sunday....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...