Jump to content
SAU Community

Recommended Posts

  • Replies 151
  • Created
  • Last Reply

Top Posters In This Topic

Ladies and gentlemen, sorry for the wait - my thanks to PranK for raising some interest in my little project here.

Without further ado, I present to you, pictures of the camera mount:

cm1.jpg

cm2.jpg

cm3.jpg

I don't have any pictures of it set up in a car, perhaps PranK will provide some later, but these photos should give you a fair idea how things work. Typically, you'll have the suction cup attached to your rear window, and the camera standing on your rear parcel shelf supported by the tripod. So, your camera will see something like this:

cmount.jpg

Initially I only made a few of these for friends like PranK, but seeing the interest shown here, I am prepared to do a 'production run'. My price to PranK was 'mate's rates' and not including the mini tripod, so price including tripod will be $80 each, less if I get plenty of orders, seeing as how this is a group buy. If you would like one, please email me (blahboy -at- iinet.net.au) so I can prepare accordingly. Cheers!

I've just gone through this thread and realised how long ago it was started - apologies to the people who were hanging out for this, PranK didn't really let on the full extent of what was happening.

If all of the people who said they were interested still are, then please, let me know now, I think the price will be closer to $70. I also noticed in the forum rules I'm not supposed to ask people to post expressions of interest... so I guess I'm sort of taking orders. Please either post here again if you want one or email me, or send a PM.

ill take one without tri pod as ive got the little tripod thingy already, $60 ??? u would be able to stick it on like the front window as well hey ???  

Clint

You can put it at the front of the car no problem.

$60 sans tripod could be achievable, it's entirely dependant on numbers. Reason is that I can source the suction cup cheaply from a wholesaler, but there is a minimum order quantity. Otherwise, if I get them retail, it will be about twice as expensive, plus each unit carries a larger burden of shipping. So if you're interested but concerned about price, step forward, and I'll work things as best I can.

is the camera hard to install?  where does it go?

The whole thing is really easy to set up, all consumer still and video cameras have a thread on the bottom that is standard sized, which attaches to the thread on the mount.

I'm afraid I still don't have any photos of it set up in a car, so here's an embarassingly cheesy sketch done by me in MS Paint in an attempt to explain:

sketch.gif

Obviously, the drawing is rough, but hopefully you get the idea. Depending on the car, the mount might be set up with the camera towards the rear glass rather than away, and if there's a real lack of room back there, then you would omit the tripod and sit the base of the camera mount directly on the rear parcel shelf. Leaving the camera hanging isn't recommended as you don't get a steady picture. Hope this helps!

i gotta say - that drawing is pretty dodgy, but also very clear.

Um, thanks? :D

thanx for that drawing cos it makes sense to me now of how it works.

my friend maybe very interested. r the final details finalised yet?

There aren't that many details - if you'd like one, you let me know. Best guess, will be $70 for the package.

Bugger it, I'll take one! I've got a great mount attached to my rollcage in the mini, and was thinking of getting one made up that mounts between the rear passenger grab rails (like the custom made WRX Club ones for WRXs). It hangs the camera right in the middle of the car... but this suction cup version is available so I might as well grab it!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
    • The old approach was to fill the cylinder/chamber with a length of rope pushed in through the sparkplug hole. The new approach is to connect compressed air to the sparkplug hole and fill it with enough pressure to push the valves up. Doing either of these things with the head on and the engine in the car is a lot less pleasant than doing it properly.
    • Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
×
×
  • Create New...