Jump to content
SAU Community

Recommended Posts

Hi all

Does anyone know about what kind of supercharger to go for on my v35 .Im currently looking at an eaton m90.Does anyone know of these,compatability,install info,etc.Can get in a raised hood to suit as well so clearance not an issue.Thanks.

Link to comment
https://www.sau.com.au/forums/topic/219366-fitting-a-supercharger-to-a-v35/
Share on other sites

hi matt,

a few things, first have you checked out the V35-specific section of the forum? there are a few that already have supercharger kits fitted and you will get more exposure to the V35 crowd there:

http://www.skylinesaustralia.com/forums/Se...lines-f170.html

secondly, a lot of info can he had on the g35driver.com forums as fitting TT kits or supercharger kits is commonplace over there. some good info here:

http://g35driver.com/forums/forumdisplay.php?f=24

and lastly, what other mods do you have on your car?

  • 2 years later...
Hi all

Does anyone know about what kind of supercharger to go for on my v35 .Im currently looking at an eaton m90.Does anyone know of these,compatability,install info,etc.Can get in a raised hood to suit as well so clearance not an issue.Thanks.

hi

I recently installed a Stillen Stage 3 supercharger on my v35, i had to cut bonnet but stillen provides a nice carbon fibre moulded bonnet scoop

hmmm, there might be an hks kit specifically for v35. saw a v35 getting fitted with a blower off a 350z, wasnt a straight swap tho(be warned)

it didnt really seem worth it honestly, sure it was punchy but was a bit lacking up top, the guy with the 350z ended up putting a single 3037s kit on, big underbonnet temp issues with that, so still not a good solution. lol

those twin low mount turbo kits kits r kinda sweet, no exhaust crossover pipe and temp issues like the hks kit. but turboing it is a whole other thread.

remember those v35's r high compression like 11+:1 from memory, dont push it too hard if its stock. wont take masses of timing or boost. might have to settle for 230rwkw or so if u go supercharged.

if possible look at a m112 off a jag v8. they come with two big water to air intercoolers. i herd of a guy who fitted 1 to a 1UZ-fe.

Screw the old chargers get the new TVS chargers - they are much more efficient. http://www.eaton.com/EatonCom/ProductsServ...s/TVS/index.htm

The R1900 would be my pick for around 300rwkw @ around 6psi of boost at 6700rpm on a 3.5L.

The stock rods would go at around 250-270rwkw from what I have heard. The high rev's have lighter rods again.

Almost any good FI setup would require forged pistons and h-beams/bearings at a minimum but then you are good for a lot more than 300. I have been looking into this for my Stagea as the VQ25det's don't have aftermarket parts available and i'm not sure how far I can push it. I cant afford to put a window in the block just yet. :bunny:

  • 2 years later...

Sorry to bring up an old post but i have a V35 sedan, looking at forced induction (VQ25DET from stagea is tooooo expensive and is for AWD and my car is RWD), looking at a supercharger but im wondering if the kit for the VQ35DE would fit on the VQ25DD Neo Di or would i have to get a custom one? Anyone know a good shop tjat is willing to do it? Any help would be great

Check this link: http://www.bulletcars.com/superchargers/rotrex-supercharger-system.html and give them a call.

First hand experience with Rotrex, they are compact and virtually silent in operation.

I'd be surprised if Bullet don't have something already to suit the V35.

Fitting a supercharger would cost much more than a S/H VQ25det conversion, plus dd's are nearly 12:1 compression, it would only work if you went e85 imo.

Your gearbox will bolt straight up to a VQ25det so it is only the ecu you need to worry about.

I have the RE4RO1B four speed which is different to the box fitted to the VQ25DET. Just want a supercharger because i thought it would be an easier task than doing a VQ25DET conversion. Plus then i can say i have a superchargwd V35 sedan with a M35 stag nose

The hks won't work without modification I believe. Ive seen and installed one. The big bracket that hangs the charger and pulleys is made for a motor without variable exhaust cam. It bolts right onto the front cover there, so I'd bet that you'd have to make a new one or modify it.

The other thing you have to worry about is your direct injectors. Who knows what capacity they are, and if they will safely support the extra fuel needed for a s/c. It's not like you can drop injectors in easily, with aftermarket support. And find a ecu to work.

Have you priced a vq25det motor? I know it would be very difficult to wire in, but it should bolt right up to your gearbox, or you could use the box that comes with it without the front shaft, or even a 5spd from v35 or 350z will go in, or a manual. It's just a matter of getting everything to talk to each other. You'd get a motor for the price of one of those kits.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was using the wiring diagram I have So 12.74V is coming into the rear Fuel Pump relay as I measured.  When I turn the key to ON im getting 0.6V to the Fuel Pump plug; which i assume is backfeed voltage and doesnt include the 12V from ignition power.  The rear relay is working and being triggered.  From the diagram I clearly see the rear relay 80 = Rear Relay going into the Body/H loom (R-27) 27 = Fuel Pump plug going into the Body/H loom (T-20) 40 = Short Connector (R-27) I'm reading 12.74V on the blue/black wire which is the power for the Fuel Pump   From this diagram I can see the Ignition relay goes into the front and up to the ignition  2 = Fuel Pump Relay <1M> (R-27) 37 = ING Relay <1M> I started from the pump using this reference Which the way I read it (referencing Nissan wiring color codes) is: Pin Wire Color Function 1 B/P (Black/Pink) Ground 2 L/W (Blue/White)        ECU Trigger 3 SB (Sky Blue) Fuel Pump 5 L/B (Blue/Black) 12V Constant Tested SB to SB on Fuel Pump for continuity - confirmed Tested negative on Fuel Pump to 12V battery and L/B - confirmed 12V Pulled the relay putting 12V between Pin 1 & 2 and testing continuity on Pin 3 & 4 - confirmed relay   So that has me looking at this part of the circuit to understand whats happening here...and im still confused. From best I can tell; the disconnect is back to my previous diagram; between Ignition Relay and Fuel Pump Relay...which yet again; afaik is where the immobiliser should.    Thats what I was trying to explain to GTSboy; im not trying to fix it myself; yet I seem to have to get a Masters in Electrical Engineering (while im busy doing my actual job of DevOps & Cloud Engineering) somehow.  I just wanted more expert opinions; or more so that what I tested is correct and proves it to something around that area; to go back to the alarm tech (for a 3rd time) that he needs to fix it. He keeps telling me its not the alarm. He lives on the complete other side of the city so i understand not wanting to make a trip but as I said before if its the alarm it should be up to him to fix it. But he's adament its not; even though I pointed out the FP was immobilised through the original alarm. To my mind; it seems that the ECU is sending the signal; but the ignition is not getting 12V down the line.       
    • Maybe also really stiffly sprung track cars. Get the inside wheel up in a corner and all the fun stops. Also me sometimes (rarely) when I have to stand on the brake to convince the diff to drive the wheel that is still on the ground when I'm trying to diagonally get over severe driveway entrance, etc.
    • I feel like I'm missing something. You had an authorised installer come out and install a new alarm. Post install the car doesn't start, and you aren't getting the installer back to fix what they did wrong?
    • So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
×
×
  • Create New...