Jump to content
SAU Community

Recommended Posts

I hope this hasnt been posted before...

Stumbled upon this and thought it was worth sharing around, even though i doubt anybody will get to do it... :)

http://jpcnews.blogspot.com/2008/06/ultima...-on-r32-34.html

Niss_R32_R35brakes.jpg

If there's one good thing about heavy performance vehicles, it's that they invariably have exceptional brakes. Throwing the braking hardware from a much heavier car onto somthing nimble and lightweight usually means loads more braking torque and greater resistance to fade. Backyard tuners have been doing this for ages, but now things have just been kicked up a notch by this, the first R35 brake caliper retrofit adapter that allows owners of "lesser" R32, R33 or R34 Skylines the chance to feel the titan grip of those 6-piston Brembos.

Niss_R35brakes_retrofit.jpg

The adapter system was developed by an as-yet unnamed workshop, although we're sure we'll be seeing something like it on the shelves quite soon. All that's needed to mount these suckers on your 90s Skyline are two hefty-looking aluminium adapters that go between the steering knuckle and the calipers, the bolts to fit them together, and those monstrous calipers and 380mm floating rotors. You'll need some big wheels to squeeze them in, but it's possible with 18-inch Rays TE37s or Nismo LMGT4s - it probably helps if you've got a GT-R too, as the extra fender width and more aggressive offset would help shoehorn those wheels in.

As for cost we've got no idea, but considering the R35 is still a relatively new model we're betting that the total for all the hardware involved would be bordering on extortionate. Better to wait until a few more R35's get thrown on the junkheap first.

Niss_R35brakes.jpg

Yeh the alloy adaptors are about $600, then you just need to get the rotors and calipers which are going for about $6,800 including rears.

So not exactly a bargain upgrade. But great to see Nissan using a radial mount caliper, if only they did that with earlier model GTRs then you would have had a cross between a Lotus and F40 caliper, only as it woudl be radial mount it would have been oh so easy to throw larger rotors at the std caliper

and the article you linked is a bit lame. not much info. for the record the workshop is Endless R. and the price is from memory 850,000JPY so about $9500 landed. and it's only front brakes.

  • 11 years later...

Would expect all offsets that you would think of fitting to a 32 R will clear based on a google search that said a +22 clears.

Search R35 18 inch brake clearance

First result that comes up from GTRlife.

Edited by djr81

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...