Jump to content
SAU Community

Recommended Posts

Hi,

A mate of mine is having troubles with his R33.

As soon as it hits about 5500rpm it just stops accelerating and starts back firing. or if it doesnt back fire it just stops reving and stays @ 5500rpm...

We are certain that is not coil packs as we have had many coil pack issues before and this isnt the same.

The car had a Power FC, Z32 ADM and a 044.

The now has a Stock ECU, AFM and fuel pump.

Also today is the first time the car has been driven since August..

Any help appreciated!!

Link to comment
https://www.sau.com.au/forums/topic/223844-r33-problems/
Share on other sites

nah if its running fine up to 5500 rpm it wont be plugs or fuel, if it was either of those it would be coughing and spluttering right through the rev range,

but will need a few questions answered before being able to tell what it is causing it, is the afm still ok, have you swapped it with that of another car?

is the car running standard boost. if it had a z32 on it was the setup outflowing the standard afm? if so take the boost back down to standard.

R33, variable timed yes, is the solenoid still operational that lets oil flow to the lifters?????

the ecu alters fuel values when the system is activated by the rpm, flooding perhaps and detonating violently?

if so unplug the O2 sensors and leave them off for the time being as the ecu would be compensating for the richness,

also unplug the ecu temp sensor, this will force the ecu to go into normal operation as if the engine had warmed up.

is the base timing correct, assuming it was running a aftermarket ecu, afm, etc was this altered at all?

Link to comment
https://www.sau.com.au/forums/topic/223844-r33-problems/#findComment-3943506
Share on other sites

It seems to have lost alot of power throughout the hole power range. But hasnt lost any boost.

Also little puffs of black smoke seem to come out the rear so it couldnt be the fuel pump if its running rich??

Could it be the afm??

Link to comment
https://www.sau.com.au/forums/topic/223844-r33-problems/#findComment-3945482
Share on other sites

It seems to have lost alot of power throughout the hole power range. But hasnt lost any boost.

Also little puffs of black smoke seem to come out the rear so it couldnt be the fuel pump if its running rich??

Could it be the afm??

Almost a thread a week on this these days… *sigh*

Your running increased boost on the stock ECU. Its therefore having a fit/hernia/spaz etc etc.

Back off the boost, car will return to normal as its closer to factory. RB25 ECU's don’t like much over standard boost pressue in many instances

Link to comment
https://www.sau.com.au/forums/topic/223844-r33-problems/#findComment-3946101
Share on other sites

It is a constant problem at the 5500rpm mark? My car is having similar issues, but its temperamental. Some days it drives great, other days its terrible, and of course whenever I take it to the mechanic it decides to have a good day, or half-week as it were last time.

In any case, next time it plays up I'm driving it straight to him. I'll post here on what he finds.

Link to comment
https://www.sau.com.au/forums/topic/223844-r33-problems/#findComment-3947828
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...