Jump to content
SAU Community

Recommended Posts

Thanks guys. :closedeyes: It's just an Evo 6 GSR (not a TME), so it has all the luxuries.

What kind of times did she do ?

It posted a 1:04.5 in it's first outing at Wakefield Park in June (at Evo Nationals) and it ran a 1:13.5 at Mallala last month at the Autosport MGEC Time Attack.

^^^^

Who built it out of curiosity?

built buy browns engineering in QLD, bored 40 thou new endurotec pistons, moly rings, king race bearings, prepd rods, crank collar fitted, rebuilt head ported new seals, lewis drain back kit, head welded n tap'd for vct, new 25 water n oil pumps, not sure if its worth putting arp rod/head bolts and a metal headgasket in or not, will need another manifold for my 3076r

post-4329-0-70238500-1352274338_thumb.jpg

I ended up going with ARP rod and head bolts. My intention was "whilst its all apart you may aswell". Shame it ends up costing a packet though!

IMO RB25/30 + GT3076R is the best combo for a responsive ball tearer combo. The midrange is obnocious!!!

  • 4 weeks later...

I ended up going with ARP rod and head bolts. My intention was "whilst its all apart you may aswell". Shame it ends up costing a packet though!

IMO RB25/30 + GT3076R is the best combo for a responsive ball tearer combo. The midrange is obnocious!!!

yer mines all assembled.. but not sure since its dry to turn her upsidedown and stick some arp rod bolts in her just for piece of mind, head bolt nissans are usually ok, and wont be running a40psi, hopefully have front end done (this is a s14a btw) and engine test fitting over the chrissy break aiming to be on track mid next year.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...