Jump to content
SAU Community

Recommended Posts

  • Replies 117
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

i remember a few years ago one guy telling me how he was running a old gas setup through his turbo car, i think it was a corolla?? he said the car backfired and the intercooler made one massive big explosion tank which went bang in a big way.

another friend of mine had a VL turbo on gas, and he would explode his air box and destroy AFM's, i remember once it happened it scared the crap out of me.

Be interesting to see how these direct injection setup's go.

I dont get it, why? A little bit more power at the cost of long term damage that might reduce the life of ur engine? Filling up every 100km and waiting 10 mins for it to fill? Wont it run extremely hotter than on fuel as gas is dryer? I could be wrong but yea lol

lp gas is 104 octane, cheap and avail everywhere....

if i had a turbo daily, say a chaser for example with just a highflow, i'd do it fer sure as i could get away with 6 injectors, and pick up a fair whack of power safely

but e85 is better for my current application (300+rwkw on lpg = 12 injectors and a lot of f**king around for only 104ron)

Yep I did :down:

Just wasn't interested in arguing how much it costs, how it's not going to work, and how everyone who's never done it before seems to know how to do it the right way :whistling:

On a side note though, for everyone chasing 120 hp per cylinder etc, I have a big question? Why? Not why is everyone chasing big horsepower, that's a given, but why does this high horsepower have to be on lpg. 99% of driving where fuel economy is concerned is going to be done sub 250hp (probably sub 200hp) and any system these days can be easily switched been fuel and lpg and good systems like mine can switch at a given rpm (I cut over to normal fuel at 6000) under normal conditions, so why not keep the big fuel system for the 6000 rpm launches with 30psi of boost, and just run the lpg the other 99% of the time?

I seen them do this to a hotrod and got arround 650hp out of a chevy 350. They said that injecting propane as a liquid just by the injection process will make 5-8 pounds of boost in the intake. Plus the octane rating is so high that it's basicly like your running race fuel but at half the cost of shitty regular. I was thinkin of building my Dodge up for propane and getting a stroker 390 11.5/1 comp built to utilize it. The only problem i found is that it's a pain to put the tank somewhere.

A few pics of tank and filler.

I went with a small tank which fits between the wheel arches so as not to lose and usable boot space. You can see from the pic that it's not obtrusive. It's a small tank, but suits for the moment. Later on I'll change the fuel tank to a smaller one and pony up a second bottle underneath.

post-495-1243992852_thumb.jpg

post-495-1243992960_thumb.jpg

Hey there this thread is interesting but as the previous people discussed Liqiud injection can be used in high hp applications with either the use of twin injectors or the new improved high flow liqiud injectors,

We have converted a few Xr6 turbos with this system and its fantastic and with a decent tune can produce in excess of 300 kw at the wheels and more, with extra injectors can go beyond this, liqiud cannot backfire as its the same principles as a petrol fuel system, just under higher pressures.

we can currently fit kits to any pre-2004 vehicles with custom setups available,

the only down side of a liqiud conversion is the cost,

in excess of 5k for a custom setup/tune but the results are amazing

my 2c worth

cheers john

What people got to remember is that octane rating is a measure of resistance to detonation or pre ignition, not the stored potential of untapped HP. The higher the octane , the slower the burn. Duel fuel cars are always slugs on gas cause there set up to run on petrol also which requires generally around 10 degrees before top dead center ignition timing at idle where as LPG needs around 20 degrees BTDC. You retard a petrol engine 10 degrees and tell me how it feels. Now bump that compression up around 13:1(for atmo), get your fuel delivery right and set your ignition to suit with a good strong spark and I garantee you will have some kick in the pants. Dedicated is the only way to go with LPG vapourised systems.

I'm not sure how far the factory ECU's will advance the ignition with factory maps and running piggy back injection systems but if you can get an aftermarket ECU with duel settings of timing and injection to suit each fuel at the flick of a switch, that's where you'll get the best out of both.

The biggest problem I found with turbo LPG is definately finding someone who really knows their stuff or even wants to. I ran around in a turbo Hiace for a few years and had a ball. Good luck to all those having a go with this. Alternative fuel research is something we all have to grab by the balls if we don't want to go back to horse and cart some time soon.

What people got to remember is that octane rating is a measure of resistance to detonation or pre ignition, not the stored potential of untapped HP. The higher the octane , the slower the burn. Duel fuel cars are always slugs on gas cause there set up to run on petrol also which requires generally around 10 degrees before top dead center ignition timing at idle where as LPG needs around 20 degrees BTDC. You retard a petrol engine 10 degrees and tell me how it feels. Now bump that compression up around 13:1(for atmo), get your fuel delivery right and set your ignition to suit with a good strong spark and I garantee you will have some kick in the pants. Dedicated is the only way to go with LPG vapourised systems.

I'm not sure how far the factory ECU's will advance the ignition with factory maps and running piggy back injection systems but if you can get an aftermarket ECU with duel settings of timing and injection to suit each fuel at the flick of a switch, that's where you'll get the best out of both.

The biggest problem I found with turbo LPG is definately finding someone who really knows their stuff or even wants to. I ran around in a turbo Hiace for a few years and had a ball. Good luck to all those having a go with this. Alternative fuel research is something we all have to grab by the balls if we don't want to go back to horse and cart some time soon.

What epigram says is dead right about the timing and I don't know of any lpg ecus that do anything about changing timing.

There are a couple of options however with an rb series engine. You can tune for lpg only if you run with LPG dedicated and then run the petrol only for startup and engine warming. Or run it as automatic duel fuel so that it runs petrol for startup and warming and cuts over from lpg to petrol at a certain rpm. Engine maps are a cross of Throttle position and rpm, so you can adjust timing accordinglyfor when it will be on LPG and when on petrol.

The best option though would be to use the RB knock map and tie in a switch to the knock sensor to have it flip to the knock map. This way you can have 2 timing maps, one for fuel and one for lpg. The only downside is that I don't know of any way to switch it back to the default map without resetting the ecu by turning the car on and off. Chances are there is a way.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
×
×
  • Create New...