Jump to content
SAU Community

Recommended Posts

I was thinking of doing it this way for my build. what PSI would you set on compressor? also would you use a torque wrench to test the bolt afterwards?

threadlocker?

cheers

rob

What ever the air tool manual recommends (usually 90psi). I wouldnt use a threadlocker on the bolt personally. I mean, the nissan manual suggests you use oil which is the opposite of a threadlocker so if they feel confident that it will hold then so do I :P

As for the testing afterwards then yeah sure if you have a way to lock the motor then go for it. But knowing the strength of most decent rattle guns ide say you would be overtightening if you went any more.

I was thinking of going into Nissan and asking them if theyve got any info in this issue.

By the way, the new bolts from Nissan are $8.50!

Shaun.

Give it a go but every nissan mechanics are not exactly the pinnacle of brain power i have found.

Give it a go but every nissan mechanics are not exactly the pinnacle of brain power i have found.

I know exactly what you mean. Every time i go to Gosford Nissan for a part, they ask me for a fcuking VIN number! As soon as they hear you say 'Skyline' their care factor goes to zero. I actually quite enjoy pissing them off when asking for obscure parts.

Hornsby Nissan, however, are awesome. They'll do anything for you.

Shaun.

Strange, 2 pages down from that diagram, theres this...

gallery_14713_1542_7303.jpg

Is that 446Nm for the crank pulley bolts?

Hi there, you all most likely know this already but for the record, the use of oil on threads of bolts to be torqued (to any value) is to avoid getting false torque settings due to "thread binding" before the bolt/nut has pulled down to achieve the stated torque setting. Regarding thread locker liquids, provided the threads (male/female ~ bolt/crank) are clean & free of binding media then I reckon liquid thread locker of the correct grade will do as a lubricant & provide some insurance after correct "pulldown" on this particular critical fastener. Thread lock compounds do not activate until all oxygen is excluded from the mating metal to metal surfaces. (thread faces) I refer to the Locktite range of products. Having said all that there are locking solutions in the Locktite range to do many different jobs, studlock/bearinglock/threadlock (several grades) select carefully.

Regarding the correct setting, the originator of the ATI harmonic balancer group buy is as stated on this forum getting his balancer installed by "dirtgarage", Red R racing?. Perhaps this fine gentleman could have the final say on the relevant Nm settings for RB25/RB26 before we start.

My 2c.

Cheers GW

PS: I absolutely hate drilling out snapped bolts/easy-outs. Even worse than housework! :D

Hi there, you all most likely know this already but for the record, the use of oil on threads of bolts to be torqued (to any value) is to avoid getting false torque settings due to "thread binding" before the bolt/nut has pulled down to achieve the stated torque setting. Regarding thread locker liquids, provided the threads (male/female ~ bolt/crank) are clean & free of binding media then I reckon liquid thread locker of the correct grade will do as a lubricant & provide some insurance after correct "pulldown" on this particular critical fastener. Thread lock compounds do not activate until all oxygen is excluded from the mating metal to metal surfaces. (thread faces) I refer to the Locktite range of products. Having said all that there are locking solutions in the Locktite range to do many different jobs, studlock/bearinglock/threadlock (several grades) select carefully.

Regarding the correct setting, the originator of the ATI harmonic balancer group buy is as stated on this forum getting his balancer installed by "dirtgarage", Red R racing?. Perhaps this fine gentleman could have the final say on the relevant Nm settings for RB25/RB26 before we start.

My 2c.

Cheers GW

PS: I absolutely hate drilling out snapped bolts/easy-outs. Even worse than housework! :banana:

Bump.

And.........whether the crank bolt is left or right hand thread?

Cheers GW

I always thought the correct torque setting for the rb26 balancer was VFT?

Double hammer rattlegun at warp 4 on full charged air reciever? :( C'mon Mr dirtgarage, I think you could help & you owe me one I reckon.

Cheers GW

Double hammer rattlegun at warp 4 on full charged air reciever? :( C'mon Mr dirtgarage, I think you could help & you owe me one I reckon.

Cheers GW

Owe you one?...were you not the fella that accused me of lieing to you? Over the sale of a Power FC..Then i proved to you that i wasn't?....I think you may owe me one. (or was that someone else with a 260?)

150Nm with ARP lube on the bolt and both sides of the washer....then 1/2 a turn more with a piece of pipe over the torque wrench handle....So Duncan was correct...VFT

Why don't you ask Sydneykid?...he thinks he knows everything...lol

Edited by DiRTgarage
Owe you one?...were you not the fella that accused me of lieing to you? Over the sale of a Power FC..Then i proved to you that i wasn't?....I think you may owe me one. (or was that someone else with a 260?)

150Nm with ARP lube on the bolt and both sides of the washer....then 1/2 a turn more with a piece of pipe over the torque wrench handle....So Duncan was correct...VFT

Why don't you ask Sydneykid?...he thinks he knows everything...lol

(150Nm with ARP lube on the bolt and both sides of the washer....then 1/2 a turn more with a piece of pipe over the torque wrench handle)

Is this for RB25 Sir? Or both 25 & 26?

Cheers GW

PS: Put the gloves away champ. I'm the guy that thort he was buying your fronts & dumps. My bad as I said then but I did wait patiently for you to make up your mind as to whether you were actually selling anything at all & at that time I did say that it would cost you down the track with technical information as my project progressed. (which were why I purchased your parts) I can post up the pm's if you like.

Peace brother, I will call on you again down the track no doubt.

(150Nm with ARP lube on the bolt and both sides of the washer....then 1/2 a turn more with a piece of pipe over the torque wrench handle)

Is this for RB25 Sir? Or both 25 & 26?

Cheers GW

PS: Put the gloves away champ. I'm the guy that thort he was buying your fronts & dumps. My bad as I said then but I did wait patiently for you to make up your mind as to whether you were actually selling anything at all & at that time I did say that it would cost you down the track with technical information as my project progressed. (which were why I purchased your parts) I can post up the pm's if you like.

Peace brother, I will call on you again down the track no doubt.

Sorry Graham...i DID have you confused with another 260 guy...my mistake. The guy i had you mixed up with is from Melb. with a very similar username. Actually it wasnt even that close..it was MyStag260

feel free to call on me anytime mate.

Edited by DiRTgarage

we did my crank bolt up VFT and it still managed to come loose and damage key way, and also bolt damage..

Autosport came to the rescue!

i think the rattle gun was on warp 10 that night and everything was very clean when assembled..

Sorry Graham...i DID have you confused with another 260 guy...my mistake. The guy i had you mixed up with is from Melb. with a very similar username. Actually it wasnt even that close..it was MyStag260

feel free to call on me anytime mate.

No worries & thanks for the info. I take it that the suitably lubed bolt/washer @ 150nm + 1/2 turn with enforcer bar (for all the ATI group buy guys) is for RB25 & 26

Cheers GW

we did my crank bolt up VFT and it still managed to come loose and damage key way, and also bolt damage..

Autosport came to the rescue!

i think the rattle gun was on warp 10 that night and everything was very clean when assembled..

Studlock it is then hey?

Cheers GW

+1 for the VFT torque setting..

the highest torque setting ive seen on any import that was legit is 300NM for 1 of the bolts in the subaru 6speed gearbox.. subaru supply there mechanics with a 3/4inch torque wrench that can do up to 600NM for that 1 bolt... f**king awesome tool! :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...