Jump to content
SAU Community

Recommended Posts

^^^^ That would be great Mark. After having just spoken to racing beat in the US about building a motor for me I am not so sure I want to sell all my organs plus any furure unborn children to have one of their engines. I am sure they are top notch, but circa 20-25k for a rotor engine build (complete long motor with turbo etc) is a bit beyond my budget.

But at the same time, happy to spend decent money to get something I hope will be reliable. Tassie is just too far to go for me to have a mechanical early on.

While RB did have a bit of a tech edge in the past with screw in ports, cooling mods to housings and so forth - even if they did use their alloy plates, ianettis they usually recommend, 2 piece eccentrics and so forth, that's well OTT.

consider going japanese? they know how to make a good rotor motor. had my FD RZ's motor built in japan at a shop called pre-stage. was bloody quick (in build time) and performed very well. Cost was reasonable too.

There's no secret sauce in any country - although some of the locals practicing the art here probably would have been more suited to wild west blacksmith occupations. Your ex-RZ went ker-blammo very shortly after the sale.

I am suffering the same thing..

i am really trying to get excited about building an early rotor to run in classic but am finding it hard to get really excited about it. Probabaly should have just kept the evo :(

One of the long time classic rotor guys did the switch this year, damaging the now 30k + Rx3 probably the turning point. There will be someone else doing the switch too next year.:whistling: With the price of rotor engine parts going through the roof, you can basically get 4 cylinder rods and forged pistons with change for two new rotor housings.

If you want to persist..... it's no Rx7 though.....

http://my105.com/lis...ls.aspx?id=3467

Hearing ya Ben. Advice I was given very early on was don't head to Targa with anything you can't afford or risk throwing in the bush.

Funny thing, guy I mentioned some pages ago with the GTR, ended up having to make lease payments on two cars after writing one of them off at TT.....when these were worth a bit of coin too.

^^^^ There are just so many ways to crash at Targa and sooo many variables. Even with the best intentions, some rain and a fluid spill or something else unexpected could easily have you off the road.... and then there is always the red mist to contend with if you get passed or are getting caught.... :)

bummer 2pee. didn't know that! :(

the RX4 on my105 looks pretty good value. especially with 2 engines and another in bits!

but yeah rotors can be a whole lot of pain. but when going well they are great.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...