Jump to content
SAU Community

Recommended Posts

Any particular reason tarmac regs still ask for a battery box over "adequately covered to prevent short circuit and leakage, in any position." as seems universal in the racing classes?

Gel cell, check - metal case, check - bolted down, check - terminals concealed with mounting bracket, check - inserting smallest commercial plastic box that does sweet FA for these types of batteries.........even inordinate amounts of hacking away and it still won't fit around rops....f #$#%^ker T01!

Not sure where that wording is from 2pee, but regulations for CAMS Australian Targa Championship event say:

"The battery may be replaced, and or relocated to any position, provided that it is located within an appropriate battery box and securely mounted. If mounted in the cockpit, it must be behind the front seat and of dry cell in construction. A blue triangle of sides 150mm indicating the location of the battery must be placed on the vehicle."

The wording could be tweaked re the box to be more general as individual setups define if a box is actually required, but I personally don't think the reg is very demanding as a cover of some kind is never a bad idea if its inside the car from a shorting point of view, in the case of working on the car, or in an off when something could come loose and touch the terminals and create an unwanted spark.

For all the messing about though, why not leave the battery where it is... and run a lithium carbon fibre battery such as what my company sells? :)

If you know how much of a weight-nazi Tony Sullens is then you might be surprised to know he left his battery in the OEM location and I sold him a 1.7kg lithium carbon fibre battery, the car would have run the 1kg version, but I was concerned it might not fire on E85 in Strahan on Leg 5 if it was too cold!... he came fouth outright from memory :)

Original battery real estate is now on-sold....and there's the small matter of the re-wire. If you'll take the loose gold coins in my pocket for one of those Li batteries though, might convince on the merits of the swap.

Wording is from Cams, typically group 2 and 3 regs, can't remember when a battery box requirement was last specified there, must have been a few years at least. Everything electrical is still covered and if it came to the case being ruptured, acid burns would only be a worry for the coroner.:D

Just my general rant, as it appears a box will have to be fabricated as no amount of putting the battery right side up, upside down or sideways will get it to co-operate with the pos plastic cover and available clearance.....seemed a good idea at the time!!

marlin - eat me!

2pee - a lack of room is the same in the case of my rx-7 too with it's new v-mount, so the dry cell is going in the car, but just with a cover over the terminals. just do what you think is the best solution from as health and safety point of view, then shoot helen an email with pics so it can be considered by the chief scruit pre-event so no suprises arise at the scrutiny check.

It's a bit half-arsed, but with the use of a hand held hacksaw blade and the wonders of adhesive backed velcro, something approximating a cover has been slid into place between the cage and the battery posts and reassembled in situ. Might make something better when the irritation level of squeezing behind the seat and monkey bars a few times pushes me over the edge.

factory fitted coke bottle? lol

liking the Orange though

yep gotta love bleeding an RB cooling system..

and as for the orange, never seen an orange one in Tassie, till i painted my engine bay,

2 day's later i walk into a bodywork's , and there's a 32 GTS4 in Ford Focus orange,

then last week i go and see one of my good customer's, and he say's "come have a look at my 200SX, i painted it Lambo orange!!"..

just my luck..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...