Jump to content
SAU Community

R34 Body Kit Thread


Recommended Posts

man i feel sick. i wanna sell my car now. people that do this to their cars should do themselves a favour and drink some battery acid.

seriously do you sit back and look at your car and think 'damn that shits off the chain'? man you must be smoking some bad ass crack.

jetspeed make a gtt gtr conversion kit

front bar

r34-fb.jpg

front guards + side skirts

r34-gtr.jpg

rear guards + side skirts

r34-gtr-r.jpg

rear bar

r34-rb.jpg

Link to comment
Share on other sites

Cara's eyelids are eastbear copies!

The do luck R34 above is actually a real kit and costs $10,000 so fyi its pretty "off tap" and yes it looks good. Sure wheels dont work but hey its his car.

Link to comment
Share on other sites

Cara's eyelids are eastbear copies!

The do luck R34 above is actually a real kit and costs $10,000 so fyi its pretty "off tap" and yes it looks good. Sure wheels dont work but hey its his car.

umm for your information, my eyelids ARE NOT copies...........they are genuine East Bear eyelids

Link to comment
Share on other sites

well unlucky for you, you paid full price and they still look hideous

is this necessary? each to their own, back on topic, the thread was going well for the first few pages with minimal chit chat and plenty of kits to choose from... shall we keep it that way?

For those interested, here are some more pics of Cara's kit, it reminds me of the C-West front bar.

post-40562-1253570847_thumb.jpg post-40562-1253570853_thumb.jpg

Link to comment
Share on other sites

I quite like that front bar, a bit much perhaps though.

Do Veilside do a kit for the GTT not just the GTR, a kit is next on my shopping list but I'm still unsure about what to get (finish off my Nismo kit, Top Secret, Impul...) I don't actually mind the Veilside stuff even though some people think they are a bgit over the top. In the end I guess I wanna keep it looking mean and stealthy.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This morning I carefully reinstalled the manifold and started looking at a couple of things I need to do.  Heat wrap arrived sometime today so I popped into the shed with the missus dishwashing gloves and started wrapping the first half of the dump and the screamer/plumb back.  Once I do the second half I'll be able to final fit the turbo and exhaust up.  Also pulled the harness out today and started terminating it at the ECU end. A connector is done, just need to run the remaining wires that arent in the harness - 12v, gnd and couple I/O
    • A31 is pretty much the same thing without HiAIDS I mean CAS, no improvement lol. Not to late to send it.
    • Thanks for all the replies! I also wanted to ask if wheels that were fitted on Ford Falcons would fit the 350GTs as well? In the area I'm at there aren't that many options for secondhand wheels and new ones here are way out of my budget. From what I've seen, most of the wheels that are available that were fitted on Ford Falcons have an offset of +33 to +36, with a centre bore of 70.5mm whereas the stock 350GT's ones are 66mm, can't seem to find any hubcentric rings that fit that difference though. 
    • 215/45/18 tyres are probably a little on the low side compared to the factory tyre, it should be closer to a 245/45/19, which will get you about an extra 11mm of height, and should make you speedo read a bit closer to reality. 245/45/19s will be a bit too far the other way and you risk a speeding ticket as your speedo might read slower than your actual speed.  245/40/19s would be correct if you are going to 19in rims, they will give you a similar total diameter to the 245/45/18 tyres.  
    • That's something I forgot to put in my list. The aggressive anti-squat in R32 is a f**king menace. I still need to decide if I'm going to drag the subframe out of my car and weld in the GKTech corrector kit. The main reason to dither is the need to switch to spherical joints in the lower arm to account for the twist induced in the rear pivot caused by lowering the front pivot. And yes...we do put better subframes in R32s, and I wish I'd gotten an S14 one instead of an A31 when I did the "take off and nuke it from orbit" HICAS delete all those years ago.
×
×
  • Create New...