Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Caltex Moorebank (Newbridge Rd) Sydney

Last night

Pump is up n running :P

Asked the Attendant if its an 85% blend or 70%

he reckons its 85% since the weather is getting warmer, and E70 is only sold in Winter when its real cold.

anyway usually when i run the stuff from United its always E85, it smells like ethanol and cold start usually stutters for a few seconds before it idles smoothly

this caltex stuff that i filled up with last night starts up 1st go perfectly so im inclined to believe that it isnt exactly E85, but closer to E70 than anything just judging from the cold start difference, and also it smells more like Unleaded than the United stuff.

Who knows

but runs the same, doesnt seem like its running richer, nor does it Knock AFAIK

post-24400-1287542963_thumb.jpg

Edited by aym23q

cool. I live just 2 mins drive from the united at rozelle but more servos around the place is a good thing. have 1,000cc injectors in the new GTR so am very seriously considering trying it out. :D

I should go past Kambah and check it out there....

But how bloody much would a full tune set me back in dyno time! fark.

It shouldn't take more than two hours to get tuned properly. Im lucky, I have a local dyno I can get on for $50 an hour now, BYO tuner. :worship:

How much were you quoted and hour?

So over the space of a few days i read this whole thread a while ago. and remember a topic on oils to use with e85.

what oils do you guys use with the e85?

Sougi 6000, discontinued unfortunately.

I used to use 300v without any issues but I would suggest you use the stock water thermostat if its a daily, as the oil needs to reach 80 degrees, to boil all the ethanol dumped into the sump at startup. (Otherwise the oil will go all milky, mine did with the low temp thermostat)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...