Jump to content
SAU Community

Recommended Posts

heloo.


i have been tying to install Nismo R34 GTR cluster in my GT,

most all working accept the speedometer end the central door lock.

engine Waring light : error speed sensor. is it possible to get pic of how it the cables are connected.


regards CB

  • 2 years later...
  • 8 months later...
  • 2 years later...
  • 6 months later...
  • 2 months later...

I have just completed this conversion and have updated the Excel document. I found an error on it and also added a few missing pin outs.GTR_Guage_Cluster_Conversion3.xls I can confirm everything works on my car, it is a GTT manual. The centre plug at the back of the cluster is different between GTT and GTR. The GTT is a brown 24 pin plug and does not plug into the white GTR 24 pin socket, I modified mine to fit using a hacksaw blade and needle file. I also swapped the lense over to the GTR cluster for the Slip and TCS off lights. 

  • Like 2
  • 1 month later...
  • 5 months later...
On 19/07/2013 at 8:06 AM, camperbob said:

heloo.


i have been tying to install Nismo R34 GTR cluster in my GT,

most all working accept the speedometer end the central door lock.

engine Waring light : error speed sensor. is it possible to get pic of how it the cables are connected.


regards CB

Hey i know its a looogshot but did you ever figure it out becuse i havet the same problem 

  • 4 weeks later...
  • 5 months later...
14 minutes ago, NZ-GTT said:

Nice work! How did you remove the pins from the connector blocks? I could not get mine out so I had to cut and solder wires.

a pin from the opposite side the wires hang out. through the inside hole.  i did this January 3, 2016 from my previous post date. the pictures are from then

  • 3 weeks later...
  • 2 months later...
  • 4 months later...

Oops good pick up! I just rechecked my pinouts and it should be 10 to 9 and 63 to 11. I've corrected the error and uploaded the file in this post as version 4.

GTR_Guage_Cluster_Conversion4.xls

On 7/27/2021 at 2:08 PM, NZ-GTT said:

Oops good pick up! I just rechecked my pinouts and it should be 10 to 9 and 63 to 11. I've corrected the error and uploaded the file in this post as version 4.

GTR_Guage_Cluster_Conversion4.xls 37.5 kB · 1 download

Thanks for the correction!

Another thing, non gtr pin 17 and pin 46 both move to non gtr pin 57.

Can you check if it is correct?

pin 17 is rear defog signal and pin 46 is charge w.l

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...