Jump to content
SAU Community

Recommended Posts

Guys, I need your advices, I have a R33 gts-t, I found it's quite scary to drive in the wet sometimes, the car starts to "Drift" when I take off in first gear to make a turn, sometimes in a hurry right turn, I feel i'm going to lose control and spin around.

have u guys experienced the same problem??? My car only has some basic mods, FMIC, turboback exhaust, CAI, standard turbo, and most of the time I run stock boost, so there is not a lot of power. I have Buddyclub N+ coilover suspension and the R34 Gtr wheels fitted, tyres are Dunlop lemans, few months old. In a sunny day, it's fine, only happens in wet.

Yeah !! I have the same issues, on wet roads, I think it's due to hard suspension. I got EDFC setup in my car and I noticed that harder the suspension I set, less grip on wet roads I get. So I always drive on softest setting on wet and just have to be very careful. I try to drive without the turbo kicking in (slow launch)

Yeah !! I have the same issues, on wet roads, I think it's due to hard suspension. I got EDFC setup in my car and I noticed that harder the suspension I set, less grip on wet roads I get. So I always drive on softest setting on wet and just have to be very careful. I try to drive without the turbo kicking in (slow launch)

Which Tein have you got??? Super street??? I set my Buddyclub N+ to softest, and it's still happened

what tyres are you running? hows the wear on them? how low is your rears, how much camber does it have? When i put my tiens on they lowered the car and gave me a fair amount of camber front and rear. the extra camber on the rear created uneven tyrewear on the inside of my tires and I could easily break traction when turning in first say to do a U or 3 point turn. It got to the point where it was quite predictable. Would also break traction in the rain on red lights if i gave it say 1.5k revs on take off.

I now have a set of good Yokos and camber kits so it doesnt do it anymore.

what tyres are you running? hows the wear on them? how low is your rears, how much camber does it have? When i put my tiens on they lowered the car and gave me a fair amount of camber front and rear. the extra camber on the rear created uneven tyrewear on the inside of my tires and I could easily break traction when turning in first say to do a U or 3 point turn. It got to the point where it was quite predictable. Would also break traction in the rain on red lights if i gave it say 1.5k revs on take off.

I now have a set of good Yokos and camber kits so it doesnt do it anymore.

Thanks for your reply, very helpful info.

Tyres are Dunlop lemans, about 3000kms old. rear is about 340mm center of wheel to guard. I don't have the camber kits, so I guess I need the camber kits to fix the problem.

I found it's quite scary to drive in the wet sometimes, the car starts to "Drift" when I take off in first gear to make a turn, sometimes in a hurry right turn

Don't hurry then. Slow and deliberate.

R34 Gtr wheels fitted, tyres are Dunlop lemans, few months old. In a sunny day, it's fine, only happens in wet.

Everyone else has covered most of it on the tyre side, so my only other suggestion is to set the suspension up to understeer as much as possible. If it rains set the rear dampers to full soft and the fronts to full hard. If the ride's a bit too harsh in the front dial it back little by little, but always ensure the fronts are a lot stiffer than the rear.

Which Tein have you got??? Super street??? I set my Buddyclub N+ to softest, and it's still happened

I'm not sure what Tein they are , coz I got them with the import, didn't bother to chech back then and didn't have much knowledge either.

It is called drving normally. It requires throttle modulation rather then just floorg it :yes:

I agree with Roy, even a stock skyline would lose traction on wet conditions. The mods make it worse (but perfect for dry conditions). So I guess there’s nothing we can do about driving when wet other than just been very careful and always keep in mind that your car is designed and moded to suit dry conditions.

Just go easy on the gas when wet.. nothing wrong with the car… J

It is called drving normally. It requires throttle modulation rather then just floorg it :P

I drive very slow on road, most of the time with the boost controller is switched off, but it still loses traction in first gear in the rain

short shift into 2nd as soon as you get rolling

fix the camber in the rear that's the main thing (I also suspect your suspension is too hard)

dunno what else to tell you, mine just grips in the wet, the rears only spin if I want them to... and that's with 260rwkw and 2way mech diff... some pineapples set to squat might help as well

when I first got the car I had hard springs in with worn standard shocks and crappy federal tyres and the thing was pretty lethal in the wet... totally different car nowadays

It is called drving normally. It requires throttle modulation rather then just floorg it :D

ZING

i can break traction in 3rd in the excel when its wet......

its all about the right foot

+1 on throttle control.

My car is stock power wise on 255 Federal 595SSs, and in the wet it is very easy to get the rears spinning, even on fresh tyres. I manage to keep traction though by keeping the revs below 2,500 rpm (even taking off from lights in 2nd) and taking it easy around corners.

It is all about driving to the conditions.

If you really can't do this, get a piece of plastic and block about 3/4 of your air filter. The resulting restriction should bring the power down so you will get no wheel spin at all :spank:

I don't have issues with traction in the wet with a fair amount of throttle, too much throttle and you lose it but I do have AWD...

How *much* power are you putting down? With how much accelerator?

You could have badly setup suspension OR bad tyres, or you could just be overestimating your car, most cars with a good LSD get sideways in the wet with heavy acceleration, but it's hard to tell on a forum what exactly is going on.

There are some serious topics on getting power down somewhere here (as in suspension, not about right-foot control :spank:)

EDIT: Oh, on corners, it could be suspension setup or it could be overestimation of the car's handling. What rating are the springs of your suspension?

And Dunlop LeMans are *ok* in the wet, not the best, I have them as well, the fact that you have 18inch rims on a GTST also means much lower profile so that's probably not going to help.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...