Jump to content
SAU Community

Recommended Posts

Here are the road safety regulation requirements for licence plates...

Must not obscure the number plate in any way, ii. Must be clear, untinted and uncoloured, iii. Must have surfaces which are flat both on the side which faces the number plate and on the side which faces away from the vehicle, iv. Must have non-reflective characteristics and, v. Must have no unusual refractive characteristics. These requirements effectively prohibit number plate covers which have curved, domed, tinted or reflective surfaces from being fitted to a vehicle. Number plate covers which have lines or other markings on the surface which go over the number plate are also effectively prohibited. Regulation 222(2)(b) of the Road Safety (Vehicles) Regulations 1988 also requires that a number plate fitted to a vehicle must be clearly distinguishable and not be wholly or partially obscured.

Pretty sure they are uniform across all states.

pfft I've got one of those license plate covers with the black lines across it.

Driven past plenty of patrol cars and even had a patrol car tail me out of curiosity, and haven't had any problems

one of many rules in place that aren't really enforced I guess, there's all these p platers around my street with sh$tbox cars and cannon mufflers and they seem to get away with them even though they can't do modifications

Here are the road safety regulation requirements for licence plates...

Must not obscure the number plate in any way, ii. Must be clear, untinted and uncoloured, iii. Must have surfaces which are flat both on the side which faces the number plate and on the side which faces away from the vehicle, iv. Must have non-reflective characteristics and, v. Must have no unusual refractive characteristics. These requirements effectively prohibit number plate covers which have curved, domed, tinted or reflective surfaces from being fitted to a vehicle. Number plate covers which have lines or other markings on the surface which go over the number plate are also effectively prohibited. Regulation 222(2)(b) of the Road Safety (Vehicles) Regulations 1988 also requires that a number plate fitted to a vehicle must be clearly distinguishable and not be wholly or partially obscured.

Pretty sure they are uniform across all states.

So this confirms i'm correct by saying this car is now deemed as a possible defect????

whoop de doo

there are people starving in this world and your worried about a numberplate cover?

you really wasted our time replying to this with that reply???? There are people starving and your making random smart ass comments???

lol jkz

You also dobbed yourself in for using your phone/camera while driving.

I was parked and the keys weren't in the ignition :blush:

pfft I've got one of those license plate covers with the black lines across it.

Driven past plenty of patrol cars and even had a patrol car tail me out of curiosity, and haven't had any problems

one of many rules in place that aren't really enforced I guess, there's all these p platers around my street with sh$tbox cars and cannon mufflers and they seem to get away with them even though they can't do modifications

That doesn't mean they wont get defected, just that they are running the risk of being defected, and their are people who get done for number plate covers.... even on these forums ive found them.... but i'm 100% sure that this rta car will never get defected for it where as if you get a smart ass highway patrol car you still have the possibility of getting done.

Ok firstly:

How do you know its an actual RTA company car? Maybe its just someone that really likes the RTA? Or has the initials RTA?

And secondly are you sure its not just a number plate frame? not a cover?

Ok firstly:

How do you know its an actual RTA company car? Maybe its just someone that really likes the RTA? Or has the initials RTA?

And secondly are you sure its not just a number plate frame? not a cover?

its even got the lines going across the numberplate in the dodgey photo....

and RTA will not let anyone choose a numberplate starting as RTA, especially RTA.002

there are RTA cars from RTA.000 - RTA.999

also its a WHITE toyota Aurion = company car lol

So this confirms i'm correct by saying this car is now deemed as a possible defect????

Well no if you'll take the time to absorb what was written, it appears the licence plate cover you have pointed out falls within the legal guidelines ie: NOT illegal.

Must be clear, untinted and uncoloured, iii. Must have surfaces which are flat both on the side which faces the number plate and on the side which faces away from the vehicle, iv. Must have non-reflective characteristics and, v. Must have no unusual refractive characteristics. These requirements effectively prohibit number plate covers which have curved, domed, tinted or reflective surfaces from being fitted to a vehicle. Number plate covers which have lines or other markings on the surface which go over the number plate are also effectively prohibited. Regulation 222(2)(b) of the Road Safety (Vehicles) Regulations 1988 also requires that a number plate fitted to a vehicle must be clearly distinguishable and not be wholly or partially obscured

Looks flat and clear, no distortion and I can't see any lines on it.

You were able to take a clear picture of it weren't you? So...

Well no if you'll take the time to absorb what was written, it appears the licence plate cover you have pointed out falls within the legal guidelines ie: NOT illegal.

Must be clear, untinted and uncoloured, iii. Must have surfaces which are flat both on the side which faces the number plate and on the side which faces away from the vehicle, iv. Must have non-reflective characteristics and, v. Must have no unusual refractive characteristics. These requirements effectively prohibit number plate covers which have curved, domed, tinted or reflective surfaces from being fitted to a vehicle. Number plate covers which have lines or other markings on the surface which go over the number plate are also effectively prohibited. Regulation 222(2)(b) of the Road Safety (Vehicles) Regulations 1988 also requires that a number plate fitted to a vehicle must be clearly distinguishable and not be wholly or partially obscured

Looks flat and clear, no distortion and I can't see any lines on it.

You were able to take a clear picture of it weren't you? So...

Doesn't matter if I could take a clear photograph of the number plate or not, it is against their own regulations. I did read what was posted and it clearly says its "...effectively Prohibited." Open the photo again, use the zoom function and you can see lines across the cover. The RTA doesn't state that lines are acceptable if under a certain width. All in all there's 8 black painted lines across the numberplate that I can still make out even though the quality of the camera phone picture isn't very good. Imagine how much more obvious the lines are in person to grab my attention like that?

I still can't see why everyone jumps to defend the RTA when they make up allot of pointless (also allot of good) rules that ultimately cost us money in fines, even unintentional non dangerous defects.

A regulation is a regulation and I don't care who breaches it, no matter how small the infringement is. They say rules are there for a reason, are they not? Not all the rules are there for safety. A friend of mine got fined for having her Registration sticker on the tinted section of her front windshield, is this dangerous? Is she a hoon? No! but the regulation for sticking the sticker says it cannot be behind any tint, it has to be on naked glass on the windscreen or the left hand side of a fixed glass window. If she can get done for that, this Car should not have black lines across the numberplate.

19" mon @ 1280x1024 zoomed, unzoomed and over zoomed.

Could be your shit camera resolution but I still see NO lines.

But hey if you say they're there thats good enough.

Lol

Edited by madbung

It's def RTA. they have reserved all RTA and RTB plates.

I can read the plate... you could ready the plate... whats the problem? Sure if one of the letters was obscured it might be an issue.

I think you're touch the tip of a much larger ice berd. QUICK call ACA with your hot scoop!

It's def RTA. they have reserved all RTA and RTB plates.

I can read the plate... you could ready the plate... whats the problem? Sure if one of the letters was obscured it might be an issue.

I think you're touch the tip of a much larger ice berd. QUICK call ACA with your hot scoop!

Yet if the police officer didn't like the RTA driver, he would defect the car for an obscured license plate...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...