Jump to content
SAU Community

Recommended Posts

If you had to use a single turbo to make 400 - 450kw ATW, what would you use ?

GTX3582R, GT3788R, T04Z ???

gogogo !

Normally I would go the Z because it won't stop at 560-600 but the 3788 will spool faster. If you don't want any more than 560-580 then the 3788 is perfect, after that, the Z is still comparable for response with the 0.99 housing on the 3788

Alright lads,

Descision has been made.

http://www.gcg.com.au/AllImage/Products/Garrett%20Spec%20Sheets/gt3788r_772719-1.jpg

For those who don't want to click the link, it's the GT3788R from GCG here in aus, very reasonably priced too actually.

only question remains.

What rear ?

0.89

0.99

1.11

I'm thinking 0.99

Alright lads,

Descision has been made.

http://www.gcg.com.a...8r_772719-1.jpg

For those who don't want to click the link, it's the GT3788R from GCG here in aus, very reasonably priced too actually.

only question remains.

What rear ?

0.89

0.99

1.11

I'm thinking 0.99

Will you be going for low exhaust manifold back pressure and cams with some overlap? If you are, then go the larger rear housing but expect less performance at lower rpm.

If you don't have a lot of head porting and have zero overlap go the smallest.

I am not sure what the runner diameter of the 6Boost manifold and the lengths of the runners but that is also a consideration.

You need to choose which direction you want to set up your engine and turbocharger.

Low back pressure system: significant head porting, properly design tubular manifold, larger A/R turbine housing and camsahfts with some overlap... aim for 1:1 exhaust manifold pressure and boost pressure.

High back pressure system: the OEM turbocharger set up is a perfect example, higher exhaust manifold back pressure to boost (i.e. maybe 2/2.5/3.0 - 1), no overlap, short manifold runners, small A/R turbine housing.

You can't do a mix of both as each one will characterise how the engine will perform.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
    • Not yet quite as bad as what we've seen a Jim Berry clutch do in an R32 GTR though when it decided to cut a chassis rail in half... Still very very gnarly and a great reason to avoid.
×
×
  • Create New...