Jump to content
SAU Community

Recommended Posts

Squeezed my in-bred 25/26 tonight. 446kw @ 1.5bar

RB25neo with 2.6 crank/pistons @ 9.5:1CR

260 9.15 Cams with VCT

GT3582R .86 rear

Dry sumped

Sucrogen E85

Vipec ecu

nice!!

what internals were used in the build if you don't mind me asking?

  • 2 weeks later...

block machined , balanced , honed oversized 0.20

crank , remachined and re heat treated , oversized acl race bearings

rods , shotpeened and prepped rods with oversized acl race series big end bearings

pistons arias forged 0.20 oversized with acl race series rings ect

tomei oil restrictor

cossworth 1,5mm drag series metal head gasket

n1 water pump

nitto high flow oil pump

nismo low temp thermostat

trust oil filter relocation

tomei sump baffles/trap doors

brand new gasket set throughout

head reconditioned with

hks step 2 cams and valve springs quite lumpy

slight porting on exhaust side

greddy adjustable cam gears

turbos , brand new garrett -5 turbochargers

hks non turbulent dump pipes

twin 3inch up pipes with 3inch magic cats (100cfm)

single 3.5inch high flow system

5inch rear cannon

autogallery yokohohama/os giken 1-5 gearbox , custom double cone syncros , hd mainshaft , hd input shaft , one piece billet 5th gear built by terry at award in sydney,,,

brand new os giken twin plate clutch

vspec active rear lsd and axles ect

nismo 320kmph dash

apexi power fc commander with hand controller

blitz ebc

injector dynamics modified 1000cc injectors on standard rail

turbosmart adjustable fpr

bosch 044 pump

splitfire coilpacks

hks dli twin spark amplifier

tien adjustable suspension

412 - 418kw @ 25psi also still running on BP 98 Octane 28s7nsz.jpg

Stock RB26 including stock cams

Precision 6262 .8 twin scroll

6boost twin scroll with twin tial 38mm gates

Custom dump and plumb back pipes

LINK ecu

ID2000 cc injectors in stock rail

Walbro 400lph

Running semi slicks on the dyno too

Gate pressure

E70

8fca5bae.jpg

  • 1 month later...

thought i'd ask in here as opposed to starting a new thread.

Midori has some 90mm front pipes now... i've got 80mm ones and not 100% on what mm the catback is... given the increased kw #'s we're putting out with E85 etc... would there be much gain in going to some 90mm front pipes? or is it waste of time unless the rest of the system is 90mm??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
×
×
  • Create New...