Jump to content
SAU Community

Recommended Posts

448kw @ 24.5psi on caltex eflex (E70)

Pump is at it's safe max limit

I rekon lines can flow more if I had more fuel flow

Are u going bigger/ extra pump?

How did you figure out the pump is at its limit, did you try more boost and didnt get enough fuel?

Got over 400kw 418.8 atw turbo runs out off puff . 26/30

That was bound to happen considering it is a small turbo (especially hot side) for such a serious engine, same result with that other fella posting in the RB30 section.

That was bound to happen considering it is a small turbo (especially hot side) for such a serious engine, same result with that other fella posting in the RB30 section.

Yes i was hopeing to squeeze a bit more but will have to upgrade rear housing And see what it goes, after i find out everything is ok with head and bottom end once i get oil samples back.

That was bound to happen considering it is a small turbo (especially hot side) for such a serious engine, same result with that other fella posting in the RB30 section.

Who is the other fella and what turbo is he running , so we can compare ?

Who is the other fella and what turbo is he running , so we can compare ?

You, haha!

I don't think people should be surprised when they build a stroker engine/head combo, put a small exhaust side (turbocharger) on there and then the power noses over early... there will be more power earlier (more 'response') which is the intent of these builds but you just wont get that peak number.

http://www.sau.com.au/forums/topic/434910-rb3026-cam-selection/page-2

An elephant never forgets, lol

Edited by bigmikespec
  • Like 2

You, haha!

I don't think people should be surprised when they build a stroker engine/head combo, put a small exhaust side (turbocharger) on there and then the power noses over early... there will be more power earlier (more 'response') which is the intent of these builds but you just wont get that peak number.

http://www.sau.com.au/forums/topic/434910-rb3026-cam-selection/page-2

An elephant never forgets, lol

HAHA why do you think I asked, I can cop it , I have been dumped on by experts :)

But you seem to forget, I did not do anything, I knew nothing and took the advice of the builder as far as the exhaust goes , he said put a new custom 3.5: exhaust on the car , I said OK I did not know he had a 3" dump and the old 3" Cat. I will fix that. Fark at that time I did not know what a dump was until you posted this :)

The PT6262 CEA will go over 700HP , this is much more than I have now or expected and yes it was built for response ,and as a stroker a little different than most .

I will struggle on, ducking the ton of shit raining down on poor little old me and hopefully end up with what I am after :)

The more I read about people's horror stories and being shafted by workshops or being underwhelmed by the outcomes of a build, the more I want to start building motors for people. It's not rocket science. In fact its almost common sense when it comes to choosing the correct components for the purpose or aim of your project. There is a huge wealth of information on this forum and I just don't understand how people can still be getting things so wrong.

  • Like 2

The more I read about people's horror stories and being shafted by workshops or being underwhelmed by the outcomes of a build, the more I want to start building motors for people. It's not rocket science. In fact its almost common sense when it comes to choosing the correct components for the purpose or aim of your project. There is a huge wealth of information on this forum and I just don't understand how people can still be getting things so wrong.

Hi Mitch, I cannot believe the crap that was dumped on me and things being over priced ?

It is not all that bad and nothing like getting married , well for the 4th time :)

It seems we are all after different results. Mine is to be able to enjoy my ride and have a shit load of GO! from the getgo!

I love the look and history of the R3s GTRs , with the money I have spent I could have bought a newer GTR , but I wanted an R3, ended up with the R34GTR and just loved the feel of the car :)

With my drivetrain mods you should drive this around some twisty stuff, just great..

So , all good :)

You, haha!

I don't think people should be surprised when they build a stroker engine/head combo, put a small exhaust side (turbocharger) on there and then the power noses over early... there will be more power earlier (more 'response') which is the intent of these builds but you just wont get that peak number.

http://www.sau.com.au/forums/topic/434910-rb3026-cam-selection/page-2

An elephant never forgets, lol

Very aggressive though might look for more numbers later for now after i sort a few things i will just enjoy the snap neck :)

twin bosch 044s, standard lines. was leaning out a bit so have just upgraded injectors, if its still running out of fuel i may have to upgrade fuel lines. tonight i will know

Any updates from today?

How are your twin 044s set up? Feeding from surge tank or standard tank?

That was bound to happen considering it is a small turbo (especially hot side) for such a serious engine, same result with that other fella posting in the RB30 section.

Hi Michael

Been reading some of your posts and you seem to know what you are talking about and I would like to get your input if you do not mind.

I did not choose the dump or cat, but I am going to change it to a 4" dump and cat. But think I will wait and see if the 3.5" exhaust system I have works in with the changes when I am getting the flex tune done ( hate the idea of tossing $2500 without seeing if it can work). If it is too restrictive I will change it to 4" all the way and finish the tune,

I am sure from what I have read 4" all the way would be better, but noisier. Mufflers could sort this out. Have to look into Mufflers now, never stops :)

The other fella :cheers:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...