Jump to content
SAU Community

Recommended Posts

Another will it fit question.... anyone that can shed light or advice would be much appreciated :down:

I am looking at getting a set of 19x9.5 in a +38 or +25 offset - can anyone confirm if these will fit my M35 250t? Im thinking the +38 offset will be the go...

I want something to fill the guards properly - there seems like plenty of room with the standards, but feeling the inside of the front tyre - they seem pretty close the suspension swing arm.

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

I want something as wide as possible to really fill the guards.

I had 8.5" wide in my C34 stagea and I think that another 1/2 inch would have filled the guards a little better. Im not a fan of spacers, So I would prefer to go as wide as possible :)

R34 GTR wheels fit very well and I beleive they are a 9 or 9.5" wheel.

I think mine are 9.5 inch but they have 235s on them which means the side walls lean in, they have to so they dont rub. The rear guard needs to be rolled then wider would fit but the front is already rolled.

Fronts also rub at full lock.

I wouldnt go bigger than 8 front and 9 rear unless you like panelbeating. :)

:thumbsup:

Noice coice Danny!

Would look phenomenal on Stephen's RS I reckon.

*EDIT* ...but you could get *ahem* "more" if they went on iain's

They do look good, I might have to pop around and borrow them when danny fits 'em lol I'll provide a couple of bricks whilst I borrow them :)

nah his car is too pink, would look better on mine!

Get over it you wankah :( seriously, just drive your bland silver stagea :P

Buy the cheap ones. Our cars have so much grip that it is much more fun on a tire which you can slide occasionally... LOL :blush:

With Andy on this one....I have to be really pushing it on Falken's to have fun....even in the wet!!!

They do look good, I might have to pop around and borrow them when danny fits 'em lol I'll provide a couple of bricks whilst I borrow them :blush:

mxfly would have all the info that you'd ever need to know about your M35 rims, if you don't know it already. PM him.

Cuff all this!

When I go for new rims on the Stag I'm going to get some 15 x 8" Valiant 440 charger rims, nice and rusty with some fat old goodyears on the back.

The rust should tie in with the Ruby red paint work nicely :banana:

Cuff all this!

When I go for new rims on the Stag I'm going to get some 15 x 8" Valiant 440 charger rims, nice and rusty with some fat old goodyears on the back.

The rust should tie in with the Ruby red paint work nicely :banana:

One word; Hotwires.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...