Jump to content
SAU Community

Car Stalled But Clutch Was Completely In..

Luckieee
 Share

Recommended Posts

eeiko321 Experienced

eeiko321

Posted
Posted
Yo i stalled my car today.. but clutch was completely in.. and normally when i stall the lights come up on dash board.. this time it didnt..

Any1 know what it is and how much to fix?

so when your car is in neutral and stalls...

on alot of cars...tbe the throttle position sensor may need cleaning.

what sort of car or maintenance on the engine?

SLEEPR85 Proficient

SLEEPR85

Posted
Posted

This has happened to me a couple of times also when the clutch was fully pressed in and been coming to a stop. Me thinks its nothing to do with the clutch though, and as others have said it feels like something to do with engine. Only has happened twice in two years i've had the car so i'm not too worried about it....

eeiko321 Experienced

eeiko321

Posted
Posted
Huh?

If the clutch is all the way to the floor, and it stalls, it's the clutch slave cylinder... or the master.

Happened to me in my car a few months back.

yeah i dont think its got to do with anything regarding the clutch

things like this are more likely the throttle position sensor...AAC ... blocked vaccume hoses can also produce this affect...and ECU faults can do this as well.

GTRsean Grand Master

GTRsean

Posted
Posted

Mine used to do it until, I got rid of the clutch line loop back block that sits in between the clutch master and slave cylinder.

Pulled that out and bought a braided clutch line from jj that goes straight from the master to the slave and I couldn't be happier with the clutch action now.

It doesn't try to stall the engine when you come to a stop with the clutch in, in gear.

3LGODZILA Proficient

3LGODZILA

Posted
Posted (edited)

it doesnt really sound like your problem, but when i replaced my o2 sensor it fixed all my stalling problems 100% (touch wood), but mine really only stalled when i bipped the accelerator and went on the brakes.

EDIT: actualy after reading through all this, most people seem to think its to do with the clutch, most likely not, wats ur idle like when warm and cold?, wat about with the a/c on? and when u steer does ur engine struggle a bit or do the revs go up? if ur idle is low all the time u probably just need to reset and adjust it. if ur idle is fine (warm/cold start and with a/c) but the engine struggles when its under load (braking at the lights, turning the steering wheel, maybe even bipping the throttle) then its probably the aac valve, air flow meter, or even the o2 sensor. how many km's has your car done?

quick question, ur not running anything under 98RON fuel are you? this will cause ur car to run and idle like shit

Edited by xdef
Munkyb0y Grand Master

Munkyb0y

Posted
Posted (edited)

when i first got my car, it had an atmo venting bov (a blow off valve that goes psssshhhhht into the air). i had this same type of stall happen to me a few times, randomly, always when coming onto the brakes with clutch in. the more sudden the action, the more likely it was to almost stall, occasionally stalling.

plumbed the bov back in. never had this issue again.

so, if you dont have a blow off valve, forget everything i said. if you do, i would consider this a high priority on your check list.

edit: i just read your original post again, and realised you may have just been idleing at the lights, not coming onto the brakes at all. if so, its prob not the bov.

dont know why i imagined braking lol.

Edited by Munkyb0y
sIIgtst Rising Star

sIIgtst

Posted
Posted

luckieee

do you often use the clutch to change the gears in your auto?? :P

if so i think that is where your problem is...

just rip your clutch pedal out that should solve the problem

Corey,

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...