Jump to content
SAU Community

Recommended Posts

Here are few more Photos of Powered Up high flowed R33 turbo with 2IU turbine housing:

Note the difference in volume of modifed turbine housing on the right:

housings.jpg

pufront.jpg

purear.jpg

Thats some cool modifications and porting to the housing.

Hi

Whats the response difference or lag difference between the G2 and the GT3040?

I have a R34 GTT Auto, a brought a GT3040(GT3082) with a .82 rear housing a while ago to put on. Now i think it might lag to much with the auto.

Am thinking of selling, to get the ATR43 G2 or get the original Skyline turbo high flowed.

PS. Only just found this forum topic and have just joined SAU

Hi there. If you are looks to make around 230rwkws with excellent street driving ability I can high flow your stock turbo to same spec as a 2530.

Hi

Whats the response difference or lag difference between the G2 and the GT3040?

I have a R34 GTT Auto, a brought a GT3040(GT3082) with a .82 rear housing a while ago to put on. Now i think it might lag to much with the auto.

Am thinking of selling, to get the ATR43 G2 or get the original Skyline turbo high flowed.

PS. Only just found this forum topic and have just joined SAU

On GT3040, boost wouldnt come on at all under 3500 (which when driving normally is annoying) with G2 turbo comes on about 2700 (only couple of pounds which count when your trying to over take). Full boost 3500 rpm.

LAG:

On gt3040 i would have full boost at around 4500

G2 1st gear 4000, 2nd gear 3500, 3rd gear 3400 5th 3200 rpm.

My opinion:

I was supposed to go for G2 from the start, and mates talked me into getting 3040 instead (M I S T A K E). Unwanted attention, got put off the road. canary.

G2 is better or as good up to 5000RPM, after that not as good but very close to GT3040 IMO. Fully legal, i recommend G2.

do you guys do replacment for standard turbos on a r33 gtr? what specs are they and how much power would the rebuilt turbos make? also how much would they cost? sorry couldnt find anythin reading through the pages only found rb25 upgrades nothing for the rb26.

On GT3040, boost wouldnt come on at all under 3500 (which when driving normally is annoying) with G2 turbo comes on about 2700 (only couple of pounds which count when your trying to over take). Full boost 3500 rpm.

LAG:

On gt3040 i would have full boost at around 4500

G2 1st gear 4000, 2nd gear 3500, 3rd gear 3400 5th 3200 rpm.

My opinion:

I was supposed to go for G2 from the start, and mates talked me into getting 3040 instead (M I S T A K E). Unwanted attention, got put off the road. canary.

G2 is better or as good up to 5000RPM, after that not as good but very close to GT3040 IMO. Fully legal, i recommend G2.

Hi

Thanks for the info. I will look at selling the GT3082

do you guys do replacment for standard turbos on a r33 gtr? what specs are they and how much power would the rebuilt turbos make? also how much would they cost? sorry couldnt find anythin reading through the pages only found rb25 upgrades nothing for the rb26.

With RB26 we normally high flow them to 2860RS spec. which works out to be the -9 configurations in your stock turbine and comp housings. they would be ok for up to 320rwkws before you need bigger turbine housings. Response wise they feels like the N1 steel wheel turbos. Not as responsive as the stock cermaic wheels.

Photos at:

http://www.digi-hardware.com/gtrturbos.htm

We can build custom .60 A/R comp and .64 / .86 turbine with OEM boltup pattern for those if required.

Hi there. If you are looks to make around 230rwkws with excellent street driving ability I can high flow your stock turbo to same spec as a 2530.

Hi

I will be looking at getting one in the future

What is the latest prices on the

Skyline ATR43 G2 0.63 turbo?

and

High Flow R34 G3 OP6?

thanks

Hi

I will be looking at getting one in the future

What is the latest prices on the

Skyline ATR43 G2 0.63 turbo?

and

High Flow R34 G3 OP6?

thanks

ATR43G2 .63 with high pressure actautor and braided oil feeding line we can do for $1530.

To high flow your stock R34 turbo cost $960 including braided oil feeding line. high pressure actautor is additional at $150 each.

With RB26 we normally high flow them to 2860RS spec. which works out to be the -9 configurations in your stock turbine and comp housings. they would be ok for up to 320rwkws before you need bigger turbine housings. Response wise they feels like the N1 steel wheel turbos. Not as responsive as the stock cermaic wheels.

Photos at:

http://www.digi-hardware.com/gtrturbos.htm

We can build custom .60 A/R comp and .64 / .86 turbine with OEM boltup pattern for those if required.

I'm curious as to whether you have done one of these custom turbo's for a GTR yet and if so any dyno graphs or similar or info :D

I'm curious as to whether you have done one of these custom turbo's for a GTR yet and if so any dyno graphs or similar or info :D

Have done few. Not as many as other turbos thou. Have also driven one. Un-tuned, car pulled hard after 4500RPM but have lost fairbit of response to stock ceramic turbos. its about 300RPM laggier then stock N1 turbos.

Hi there. If you are looks to make around 230rwkws with excellent street driving ability I can high flow your stock turbo to same spec as a 2530.

Sounds very interesting, what is the price on this for an R34 OP6 turbo?

Sounds very interesting, what is the price on this for an R34 OP6 turbo?

Convert that into OP6 R34 turbo cost $1000 including braided oil feeding line and oil drain adaptor.

To do this we have to modify T28 bearing housing to suit a T3x pring turbine housing.

Have done few. Not as many as other turbos thou. Have also driven one. Un-tuned, car pulled hard after 4500RPM but have lost fairbit of response to stock ceramic turbos. its about 300RPM laggier then stock N1 turbos.

I was thinking if you could use the new VARA turbo's that your making in a GTR...maybe not :D

I was thinking if you could use the new VARA turbo's that your making in a GTR...maybe not :D

Probably not at this stage. They are too small to work with.

Standard from $800 + GST + oil line $80 = $960

Powered up high flow from $1100 + Oil line $80 + $150 High pressure actautor = $1310

Standard from $800 + GST + oil line $80 = $960

Powered up high flow from $1100 + Oil line $80 + $150 High pressure actautor = $1310

This might be a silly question but is it possible to just replace the standard ceramic turbo wheel with a steel turbo wheel so that boost can be raised safely above 12psi? Do you offer a price for that? Would it still require a different oil line?

We actually build a brand new turbo core with bigger wheels, then machine your stock housings to suit it. We only use steel turbine wheels. So are you actually getting back a brand new turbo inside your factory housings.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...