Jump to content
SAU Community

Recommended Posts

Hoping mine doesn't get same issues with the .63 rear, however should be easier to hold 20psi externally gated yeah?

My cooler is 510x250x70 , tube and fin, which is worrying me a bit, however can't go any wider due to auto spoiler motors for the flip down lip on the 31. Could go to a 510x300x100 probably max.

^The only thing I'd be worried about is heat soak, not boost control.

Hoping mine doesn't get same issues with the .63 rear, however should be easier to hold 20psi externally gated yeah?

My cooler is 510x250x70 , tube and fin, which is worrying me a bit, however can't go any wider due to auto spoiler motors for the flip down lip on the 31. Could go to a 510x300x100 probably max.

what power are rou aiming for? 510x300x100 is a fair sized cooler. See how your current cooler goes first though as its far from tiny tiny. Depends what your goals are and uses for the car. Sorry if you mentioned this on the previous page.

Aiming for 290-300rwkw on 98 with the ATR43SS2 op6 version, which tao has explained has a larger rear wheel to suit the .63 rear housing. Yeah i don't think it will be an issue and its piped very direct, not a return flow or anything, just all these stories in this thread are making me worried about it haha. i hope it doesnt drop alot of pressure across core.

  • Like 1

hey stao, looking for a turbo eqivilient to a t28bb/ but no bigger than a gt2860rs for a sr20. would i be right thinking it would be a ss1pu .64 and looking back through results do you have any for a fairly standard non cammed non vct s13 with standard mods 3" intake exhaust z32 550cc etc?

The ATR28SS15 would be a perfect turbo for your application. I didn't look into some thing even smaller as it doesn't make that much of a difference in response but did loses quite a lot of power.

I've handed drawings of two more sets wheels to be engineered for the GTR. for main time, I've picked up a members R34. Its got 170,000KMs on the clock, average condition, with heaps of ice and minor engine mods done by a 20 year enthusiastic. probably due to the mileage, this engine feels pretty rough compare to my other two skylines. This might be affecting performance on the dyno.

carfront.jpg

Condition of this car probably represents the majority of R34s on roads today. I will be installing commonly seen mods including a Blitz return flows cooler kit. the goal would be around the 330rwkws mark on Pump fuel, internally gated bolton. Will upload dates as project moves along.

  • Like 8

Some results sent in. This is a ATR45 SAT version on an Rb25det Neo motored Stagea, Dyno dynamic roller dyno shoot out mod. Final result of 400awkws (red) on a 36 degrees day, against a turbocharger that was previously installed.

Unopoened engine, factory cams and cam gears. Usual mods and E85 fuel.

atr45sat.jpg

Good example of an externally gated setup out of factory exhaust manifold.

externalgate.jpg

^^^

I think you will need to preload the actuator alot more then where it currently is. Was this SS2 built with a black .70 comp housing or a smaller .60 comp housing?

make no differences. the one with .60 housing is easier to install, black housings with 4 inche inlets are .70. Preload your actuator by a further 5mms, go for a drive and keep an eye on the boost gauge to see if that have made any changes.

  • Like 1

Quick question, I've still got the ATR43SS2 in the car and it's been going great. I've noticed that it sounds louder on boost after a recent track day, is this any cause for concern? It still boosts up to 20psi like before.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
    • Yeah, shame. Maybe  driver's carpet is available 🙏. I am waiting for both amayama and nangun to confirm.
×
×
  • Create New...