Jump to content
SAU Community

Recommended Posts

well it just seems like you are making it a big deal that i am chooing to want to supercharge my skyline, and it seems like you dont like the fact that i am "stepping out of the square" and doing something different.

and if i want to go wank facter then i will.

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

you can do whatever the hell you like, i'm not going to lose any sleep over your choice.

i was asking why you'd go with a blower that offers very much the same characteristics as a turbo, except at a higher price..

if i was to go a supercharger, i'd be aiming for something with no lag, and a very broad power curve, rather than a peaky figure that a turbo can deliver.

ok so let me get this straight,

you are spending more money than the entire car is worth,

to do something "different"

for results that are far less than anything conventional (tried and tested that works and is good)

and you expect everybody to post and say

"yeah awesome idea"

"i like how you have chosen to spend more money for less gains"

not everyones going to agree and say different is better

you must know that, so no point getting all annoyed at everybody who tells you so.

unique400x300.jpg

most people who spend 100,000 on a car are buying something like an R35 GTR, or are pulling off a tax scam (and don't tell me half the big money autosalon entries aren't tax writeoffs). you're getting into debt to build this. just seems like you're making emotional decisions instead of rational ones that's all, and I'm sure half the people posting "against" you are trying to point that out.

everyone loves an innovator, but innovation at what cost?

most people who spend 100,000 on a car are buying something like an R35 GTR, or are pulling off a tax scam (and don't tell me half the big money autosalon entries aren't tax writeoffs). you're getting into debt to build this. just seems like you're making emotional decisions instead of rational ones that's all, and I'm sure half the people posting "against" you are trying to point that out.

everyone loves an innovator, but innovation at what cost?

dont argue with woman logic

in any case... if you want some pointers from guys who've done it before, have a good read of this thread:

http://www.driftworks.com/forum/drift-car-...rift-car-8.html

The build itself is fuckin epic.

They used an RB30 engine (aus spec RB30 block with RB26 head) and a Kenne Bell 2.8H twin scroll (which IMHO is the sweetest sounding supercharger when mated to a big Ford 5.4L).

http://www.kennebell.net/superchargers/for...elby/Shelby.htm

There's also a R34 drag car in NZ that runs 660hpish on a Procharger F1R Supercharger, again bolted to an RB30.

Well there are two main problems with a vortech supercharger the first is lag, just like a turbo and the other is the considerable mechanical effort required to turn the supercharger.

Advantages are that they are compact, the boost increases at higher rpm so as to maximise the power adding potential, and they are incredibly efficient compared to roots and screw type superchargers. They are also quite cheap compared to a roots or screw.

If it was my money I would be doing something totally different, but its not its hers and I am intruiged by this whole project honestly because its not what i would do.

Cara, he did ask a simple question and its quite an easy one to answer - retract the claws.

EDIT: Also I just read your comment about there not being much lag due to tune. The only way to reduce lag on a supercharger is to increase rotational speed - i.e. increase engine rpm. Its not a turbo, tune won't help.

Edited by R33_Dude

dude, i think i might just add, that the supercharger i am using is a centrifugal supercharger.

and no, lag is not an issue, because the supercharger dosent have to spool up like a turbo! and the fact that they are driven by the crankshaft,

and the root and screw type superchargers, are two totally different types of blower to the one i am getting.

Let people be, everyone no matter what do things people don't agree with or understand.

Like Cara building her car, I'm building a ford corsair.. Yes a ford corsair, it will be running a nissan awd system, now many of these do you think there is, considering there is no such thing in the world asaik of an awd ford coresair? Now I know I can spend a shitload less and have something better in everyone elses eyes but I'm building this for me and you would not believe the amount of people who have tried to stop me saying it is stupid for the amount i will be spending.

Project cars are project cars they always cost a shitload and things always get blown way out of proportion, that's what makes them so fun :) haha

Edited by Eug
thread clean up

Well to start off...

There is nothing about you doing this that makes sense....but thats kinda cool :)

Your money could be spent better elsewhere, but it were going to race it then I am sure you would.

You obviously have researched this and are keen on doing it, so I say good luck to you.

You WILL have problems and plenty will go wrong....there is no doubt, i had problems going from an rb20 to an rb25 and still sorting out issues

It WILL cost more then what you planned, it always does no matter how in depth you have gone into it.

You WILL get better bang for bucks from a turbo...but you aren't after that.

Did I mention good luck with it and that it is a crazy idea!!

Will be interesting to see in the flesh when it's done...as long as you don't polish everything under the bonnet or cover everything in carbon fibre.

Again good luck and keeps us posted or blogged, should be good to see what you can fit into the engine bay of an R34.

Cheers Ro. :thumbsup:

hey dude thanks

i wont be polishing or carbon fibreing everything under the bonnet lol

the piping will be made of the same material that my intercooler piping is made up (aluminium or some shizz?lol) so that will prob be the real bling bling part of it!

Good luck with the charged project it is great to see something different, we do a lot of chargers here on big displacement v8's and i love them to death.

Honestley im not a big fan of them on smaller engines as they need to be revved hard ( see boost graph, ive included a typical charged graph too, overlayed with a turbo curve.) to gain the most benefits the power is way too linear (like a 45 degree ) turbos tend to make more much more mid and similar top end. Hopefully the builder can adress this and im sure he / she will.

In my experience the little bit of bottom end gain is not worth the mid range loss on smaller capacity engines.

Here are some nice charged cars weve had in lately.

post-34927-1240920831_thumb.jpg

post-34927-1240921447_thumb.jpg

post-34927-1240921577_thumb.jpg

post-34927-1240922077_thumb.jpg

post-34927-1240922239_thumb.jpg

Edited by URAS
dude, i think i might just add, that the supercharger i am using is a centrifugal supercharger.

and no, lag is not an issue, because the supercharger dosent have to spool up like a turbo! and the fact that they are driven by the crankshaft,

and the root and screw type superchargers, are two totally different types of blower to the one i am getting.

I realise they are different. I was pointing out to someone who posted earlier on as to why you would use a centrifugal supercharger.

I will say this, and I will say this clearly: Centrifugal superchargers experience lag. On small capacity applications they only reach usable boost (psi gained minus rotational force required) at around three thousand rpm.

Here are some references to prove what I am saying:

"Due to its design and lack of low-RPM boost it is often employed on near-standard compression engines" - http://en.wikipedia.org/wiki/Centrifugal_supercharger

"One of the disadvantages of the centrifugal supercharger is that the centrifugal compressor works best over a rather small RPM range" - Sport Compact Car Engine & Driveline Handbook (You would have to buy this or look it up on google books. Page 27, near the bottom.)

It is also in my engineering book on superchargers, I would scan it up for you but alas I have no scanner at the moment and the book is packed away with about a million others. It says something along the lines of centrifugal superchargers building boost with RPM, however lag conditions are created at low RPM, hence why they can be used on mechanically standard engines as the volumetric efficiency of an engine falls when RPM rises. Thus the supercharger compensates by increasing air flow at higher RPM improving power, response and torque throughout the upper mid range and top end.

Essentially a supercharger isn't a supercharger. Screw superchargers produce constant boost. Roots superchargers produce boost down low but seem to lose steam at the top end (quite inefficient too). Centrifugal suffers at the bottem end but the trade off is top end.

EDIT: I have another quote from Sports Compact Car Engine and Driveline Handbook: "Thus even though the centrifugal supercharger is connected to the crankshaft, it still suffers from power lag, a non-linear power delivery sometimes worse than that of even a fairly aggressive, large sized turbo."

HOWEVER

"Centrifugal superchargers are more thermally efficient than the roots blower"

Just as I have been saying all along. But no I can't be right.

 

Edited by R33_Dude
of course you can't, you have a differing opinion!!!

So how is what she is doing wrong??

Yes there are cheaper ways of getting power and better gains from having a turbo charger...but she is not after that.

So why pursue on the idea?

You and I may not do it cause there are the better ways.

She wants something different.

I am sure there a better trackable cars then your R31...but you like it.

So how is what she is doing wrong??

Yes there are cheaper ways of getting power and better gains from having a turbo charger...but she is not after that.

So why pursue on the idea?

You and I may not do it cause there are the better ways.

She wants something different.

I am sure there a better trackable cars then your R31...but you like it.

Buddy.... Did you have a look at that fork picture on page 2 of the thread?

If you did, have another look, it will explain EVERYTHING.

They aren't saying what she's doing is wrong, they are saying that you can have something more powerful, more drivable, with LESS cost.

People are usually rational i.e. comparing projects with cost vs benefit analysis.

This idea appears irrational to me.

Spending that much money merely to have a supercharger.... WA WA WI WA!

You've got my complete respect now...........

Once your car is done, can we meet up and get freaky in the back seat?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...