Jump to content
SAU Community

Recommended Posts

Just now, Hank Scorpio said:

Or if you enjoy punching the underside of the dash with your knuckles ever time you put the handbrake down.

That's quite a specific requirement but you gotta go with what works. 

  • 2 weeks later...

I have not looked back since getting a Audi Q7. Can tow car, trailer and several hundred kilos of tools, fuel and 3 mates like most cars going to shopping centre.

A good 10yo one is now probably under $35k.

 

 

158.jpg

  • 4 weeks later...
  • 1 month later...

Oil change every 7.5k $150

oil and filter every 15k $300

new rotors every 50k $500

pads every 30k 250

one satnave in 300k $1000

power steerin 1.5k

blower fan $400

new battery $550

water temp sensor $50

also did diesel pump belt and water pump at 200k ( this didn’t need doing but fingered I was in it for the long hall)

Every 100k gearbox and diff oils 1k

 

tyres last 40k(rear) 60k front

1 minute ago, ActionDan said:

Excellent info, much appreciated. 

It's a turbo diesel right? 

So when are you expecting turbo/injection pump to shit the bed? 

Trans still happy? 

Updated above post

 

still going it’s due for new oil at 330k will report back then

So the big ticket items are still to come. 

I assume it's got direct injection as well so 6 very expensive injectors + injector pump is a good few K (same as any modern SUV now), turbo will be whenever it goes. 

 

 

 

 

200 if you want to go off-road 

q7 tows as well but much nicer when not towing

which is 90% of lyf

landcrusher always wins on resale cause Toyota fan boys but all the 50k landcrushers r 250k on the clock so just buy new as money wise it’s a similar depreciation 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...