Jump to content
SAU Community

Recommended Posts

See i told you they'd make a difference!

I have the Gordgee ones on mine and the build quality is well the best you can get. And the support was great too. They came in a RHD kit and with RHD instructions. There were 10 wires 4gauge each.

I actually wrote down all the lengths of them when I got them so I can duplicate them if needed, but I forgot to post them up and have since lost the measurements... sorry! I don't think it would be difficult to make some up yourself, but if you don't mind paying the 230 odd dollars to get them as I said they are great quality.

When I installed them, I installed them in stages to see where the difference was made. I actually drove around for months in between and got a good idea if they made any difference. No I didn't remove any cables between stages.

1) I installed the six cables that go round the block and chassis first - no difference.

2) Then I installed the cable that goes from the block to the negative battery terminal - night and day change. Car started quicker, more responsive throttle, gear changes quicker(on the CVT)

3) Cable between the ECU and TCU - Didn't notice any discernable difference

4) Cable from the block to the transmission - No change again

5) Cable from the block to the ECU - No change again

So, if I was to build them myself I would install the cable that goes from the engine to the negative battery terminal first and see if it made any difference and maybe leave it at that.

If someone is willing to do a test when they receive their batch of cables, could you install just this wire first and see if it makes a difference? It's been bugging me for a while now :laugh:

Cheers.

  • 4 weeks later...
  • Replies 212
  • Created
  • Last Reply

Top Posters In This Topic

I bought a generic grounding kit from HK (well, bought it 3 years ago for about $50 AUD) and it comprised of 5 cables, but reading this thread, it seems that I am missing 3!!! (in order to be just as good as the US kit)...

I have wired up mine a bit differently though....And I'll take a few pics to show you (after tomorrow's VIC Meet). The only cable I think is an 'essential' is the tranny one, so I am gonna find another wire to do it.

can you post pic on yours??

those who installed the tranny cable, just wondering how far up you need to squeeze underneath?

With the car jacked and on stand, is it easier to squeeze in from the driver side (since the instruction said it was on US' passenger side),

or is it easier from the front on?

  • 5 months later...
can you post pic on yours??

those who installed the tranny cable, just wondering how far up you need to squeeze underneath?

With the car jacked and on stand, is it easier to squeeze in from the driver side (since the instruction said it was on US' passenger side),

or is it easier from the front on?

As above, what's the best way to install the tranny cable? I should probably get some jack stands first but perhaps it can be done with just the car jacked up? Everything else installed pretty easily, haven't gone out for a drive yet tho but is an ECU reset really needed before any potential changes appear? thx

  • 1 month later...
  • 3 weeks later...

Fitted the earth kit today and found out that the AT wire is too short and cant reach to the transmission on my V35 250GT!

Its about 5cm too short.

So for now i leave the AT wire off and all other wires fitted with no problem.

The instructions came with the kit is easy to follow but the photos would be great if is in colours and not just black and white.

Anyone fitted the AT wire to the transmission?

Here is a photo of the kit fitted:

IMG_4533_Medium.jpg

Edited by Son Gokou
  • 2 months later...
  • 2 months later...
  • 1 month later...
  • 3 weeks later...
hey guys i bought the sxexcx kit and i installed it al but just the at wire i cant seem to find where to the tranny it connects, any help? - or a pic would be awesome too.

On the transmission dipstick, use the existing bolt.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
    • Unsolicited advice? Keep the engine as close to stock as you can. Nothing wrong with adding some boost and making a little more power, but given where you are, you really don't want to try to make it into a monster. I can't imagine the roads are up to it, and the lack of locla support when it grenades will be a ball ache. FWIW, If there is a dyno around that you can access, then brand new injectors are a good idea, which will lead you to (at least) putting a Nistune in it, which will allow you to put an R35 AFM on it, all of which will make it possible to make it much much nicer to drive and live with.
×
×
  • Create New...