Jump to content
SAU Community

Recommended Posts

Hi people. Well the slide hi-flow is now out and it is now time for the 3076 to go in. In regards to the studs in the standard manifold is the best thing to get them out with is some CRC and vice grips? Also should i change the standard manifold or will this be adequate. Finally the water line that goes from the turbo to the rear of the engine, how do you get this sucker off? Any help would be appreciated. Thank's :thumbsup:

Link to comment
https://www.sau.com.au/forums/topic/273729-pre-turbo-install/
Share on other sites

Studs - you are more than likely to break a couple mate. CRC them a few times during the day and leave overnight to give you the best chance at getting them all out

Stock manifold is fine

And water line - with a bit of elbow grease, again perhaps CRC overnight.

The fun continues as i have now removed the manifold because i noticed four were broken. Is it fairly easy to take the broken one's out with the right tool's or should i call in someone. In regards to spacer plate and oil lines the turbo will be coming in full bolt on kit form (spacer plate, oil and water lines nuts, studs, gaskets etc).

IMO get rid of the waterlines, i dont see a point for them, when there's hot water running through them all the time.

As for where it ends up is behind the intake manifold, undo the 2 bolts on the head, if the hose doesnt come off you can always chop a bit hoes off, rust normally cramps it and its hard to remove.

What do you mean you dont see a point for the waterlines...? The turbo is water cooled!!!

As for the broken studs - call someone in. Its not that expensive and there are mobile guys in each state :)

Try get your others out first though, likely more will crack.

Thank's for all your imput guys. As far as the bolt for the water line behind the block do i have to really take the driver side rocket cover off. I have to admit though i've tried about five times now and cannot even get the spanner onto it.

Also make sure your oil lines are correct because using stock oil line is a no no. When i had my hypergear installed bymyself... i didnt get told to install a aftermarket oil line so therefore it blew up. So make sure u get an oil line.

That cleared my miss thoughts, ive been running an rb25 turbo without them for a while, guess it couldnt be good for the ceramic wheel.. :(

Id be more worried about the core.

A ball bearing turbo by nature requires less oil to lube the bearings. The offset to this less oil means there is less cooling going on.

Hence ball bearing turbos are ALL water cooled.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...