Jump to content
SAU Community

Recommended Posts

Hi everyone,

After recently purchasing my '96 R33 with a 3" Turbo back exhaust, boxed POD, solenoid boost mod (7psi) stock SMIC and Turbo I'm concerned that I should get the car Dyno tuned. With these mods would it be wise to get the AFR's checked and a general tune done? or would it be a waste with only minor mods. Could anyone recommened a reputable workshop to go to on the Gold Coast ?

...Last thing I need is for something to go Bang!

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/278025-dyno-tuning/
Share on other sites

Is it running the standard ECU or an aftermarket one?

As above, there's no real way to tune the stock ECU - plus it should be fine with those pretty common mods.

If it's aftermarket, alot have hand controllers which you can check knock readings and other info

Edited by mr_scary
Link to comment
https://www.sau.com.au/forums/topic/278025-dyno-tuning/#findComment-4699529
Share on other sites

Hi everyone,

After recently purchasing my '96 R33 with a 3" Turbo back exhaust, boxed POD, solenoid boost mod (7psi) stock SMIC and Turbo I'm concerned that I should get the car Dyno tuned. With these mods would it be wise to get the AFR's checked and a general tune done? or would it be a waste with only minor mods. Could anyone recommened a reputable workshop to go to on the Gold Coast ?

...Last thing I need is for something to go Bang!

Cheers.

a dyno is never a bad idea if you have the cash as it can give the mechanic and indicator if things are on there way out, eg fuel pump, blocked exhaust etc..

Link to comment
https://www.sau.com.au/forums/topic/278025-dyno-tuning/#findComment-4700054
Share on other sites

Thanks Fellas,

It is running the stock ECU no other management in place, and it runs without any issues. So a dyno would only be good to show numbers and look at the AFR's but there would be nothing that could be done as far as "tuning" or fixing the AFR's.

Puts my mind at ease about that issue then.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/278025-dyno-tuning/#findComment-4700338
Share on other sites

get a aftermarket stoichemeter (i cant spell it can you) mounted to an exhaust o2 sensor that will give good indication on how its going during driving im going to put one in my car, hooked up through the e11v2 though. your car would/should be fine but have terible fuel economy tho

Link to comment
https://www.sau.com.au/forums/topic/278025-dyno-tuning/#findComment-4700466
Share on other sites

go call Toshi, spend that O2 Wideband money on a remap that's actually worth something!

thats the shot i was just thinking for piece of mind for him. but if more mods are on the way than dont bother go get a ecu best thing i ever did aside from a turbo.

Link to comment
https://www.sau.com.au/forums/topic/278025-dyno-tuning/#findComment-4700835
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
    • meh, it was a good video, clear about the issue and how he dealt with it. A bit heavy on the RTV and very brave to put an RB in anything without rebuilding it first, but otherwise I thought it was good Dose, I'm not sure that having the pickup forward is a big issue; yes of course the oil could shift under brakes but the sump should never be empty enough for that to be a problem (unless you also have a higher volume oil pump, and that oil can't return from the head to the sump quickly enough)
    • I can donate $100 to your upgrade fund. So long as you can donate the IC7 my way....
    • I'd love a Haltech ECU, and Haltech 10 dash. Was having a chat with Rob and Andy @ Haltech when Rob put one in his MR2. First one I'm kind of interested in too, as you can dim it RIGHT down. Andy was saying bright dashes is one of his peeves too!
×
×
  • Create New...