Jump to content
SAU Community

Recommended Posts

I know there are lotsa topics comparing these turbos but just need you guys to help me decide which one to choose according to what i have available... Can get a second hand x2 Trust 517Z wit stainless manifold and trust dumps and front pipes. just been rebuilt.. for $3000 without gasket kit and whatever else to fit.. ORR brand new Garrett 2860'7's wit gasket kit for $2730 new.. ORRR HKS GT-SS complete kit brand new for $3100...This is for my GTR.. What do you guys think would be the best value out of the lot ??????? Help much appreciated, been trying to decide for days.. Also im not after huge amounts of power, just want to get rid of the factory bombs... If i were to get to garrett or HKS i would probs still get dumps and front pipes...So i guess that has to be factored in...

Edited by ChakGTR
  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

get a price on 2860 -5's (can make around 500-550 i think)

the 2860 -7 can only make about 400-450ish i think maxed out

wat supporting mods do u have? wat power are u aiming at? are u aiming at building the motor up if its not already forged? is the car for street or track use? all these things are gonna tell u wat turbo kit you should be buying

give this a read too..

http://www.skylinesaustralia.com/forums/HK...ust-t32258.html

Edited by snozzle
get a price on 2860 -5's (can make around 500-550 i think)

the 2860 -7 can only make about 400-450ish i think maxed out

wat supporting mods do u have? wat power are u aiming at? are u aiming at building the motor up if its not already forged? is the car for street or track use? all these things are gonna tell u wat turbo kit you should be buying

give this a read too..

http://www.skylinesaustralia.com/forums/HK...ust-t32258.html

Im just wanting it for road use.. Not too much lag.. Iv'e made my mind up on these three turbos particularly the Trust 517z but just want to know if this is good value compared to the others listed..?? Ive currently got exhaust 3", apexi pods, Power FC, Gizzmo electronic boost..Will be tuning once installed....Might buy some injectors and Upgrade fuel pump too..

go the -9 as they flow a little better than the -7's and less lag then the -5's; keep your purchases to garrett as they are easily repaired in australia so there is no need to seek outside help from japan for HKS items.

i have trust t517z 8cm. i like it. strong mid range power. peak power also not bad. here is some info from a old thread.

517Z's(not mine), 2860R, HKSGT2530@24psi and 2860R on std manifolds@26psi my t517z 8cm on 20psi.

At 95km/h, 85kw 95kw 90kw 85kw 111kw

At 112km/h, 105kw 140kw 130kw 130kw 208kw

At 128km/h, 155kw 240kw 200kw 200kw 275kw

At 145km/h, 255kw 305kw 296kw 317kw 305kw

At 160km/h, 330kw 325kw 315kw 350kw 340kw

At 178km/h, 360kw 350kw 355kw 361kw 343kw

At 194km/h, 365kw 358kw 372kw Chart stops

2 more timing = 370kw. but more knock, i don't want it. with the 343kw tune the knock only go up to 18.(no idea on track)

different support mods also make the power different:) i know t517z is not bb turbo, but my t517z has done 35000kms on it, still running strong.

hope you can find right turbo :D

-9's are about 1100-1200ea... makes sense you would buy those as they are the cheapest.

They are cheap because unlike the -5 and -7's, they don't come with wastegates, have to buy them seperate

if u want to use ur car as a daily, go the -7 or -9 (i have never heard of -9's tho?)they will both give u good performance inside the stock motors safety limits

id recommend the -5's tho as they make alot of power for street use just incase u wanna build your motor up and avoid upgrading turbos again

+1 for aussie turbos as they are cheaper and less hassle to rebuild which u wont have to worry about anytime soon anyway

hks do make better turbos in the big singles but wen it comes to the twin turbo setups, garret turbos are just as good

im running 2860 -7's at the moment with full exhaust but still has the stock airbox, everything else is stock, im making 232kw on 13psi on stock ecu, hoping to make around 280kw with a tune on higher boost, they are pretty much same as stock turbos, maybe abit bigger, but steel wheel and ball bearing, but thats plenty of power for me...

Edited by snozzle

http://www.turbobygarrett.com/turbobygarre...9R_707160_9.htm

Turbochargers > GT28 Family > GT2859R - 707160 - 9 print turbo comparison sheet

* Ball bearing

* Oil & Water-cooled bearing system

* T25 turbine inlet flange with threaded bolt holes instead of traditional through holes

* Standard T25 oil drain flange

* Turbine housing has a unique "compact" 5-bolt outlet that is not interchangeable with traditional T25 5-bolt outlets

* Turbine housing is cast from high-nickel "Ni-Resist" material for extreme applications

* Turbine wheel is cast from "Inconel" material for extreme applications

* Direct replacement upgrade turbocharger for GT2556R (702987-7) on Nissan RB26DETT used in Skyline R34 GT-R

* Great size for applications w/ packaging constraints

* Ideal for smaller displacement engines making up to 330 hp

* Actuator not included

HKS turbo's always outperform Garrett and Trust....always.

HKS is the best choice.

Pretty sure the Oz publications did a turbo shootout with a bunch of twins where if I remember rightly the T517Zs provided the best all around performance? They certainly seem to be the goods.

Actuators dude... actuators...

It clearly says

* Turbine housing has a unique "compact" 5-bolt outlet that is not interchangeable with traditional T25 5-bolt outlets

* Turbine housing is cast from high-nickel "Ni-Resist" material for extreme applications

^ in bold - means they have a rear housing mate, always have, always will

Plus most places supply an actuator as part of their price anyway

Pretty sure the Oz publications did a turbo shootout with a bunch of twins where if I remember rightly the T517Zs provided the best all around performance? They certainly seem to be the goods.

One of the Vic circuit boys had these and even the generic Garrett's were better. That shootout your refering to was done with different cars...a telling factor in my opinion...the 517's graph looks like it was done in 3rd gear...they were results correlated from data gained over a period of time from the dyno's ecu memory on different days and possibly different years. If i remember rightly it was Tillbrooks dyno data that was used. The Vic. circuit car did a back to back.

that is without doubt one of the stupidest things i have seen written on this forum...

My statement was not stupid at all...its based on facts and actual 'back to back' testing on the same car, dyno, driver and racetrack.

Quite often im asked how i get such good results...simple...i now only use HKS turbo's. Currently using the following on our cars HKS2510's (street) HKS T04Z (circuit) HKS T51R SPL BB (drag) and have used in the past HKS 2530's and HKS GT-RS's. All turbo's have performed with better results from any of the 'equivalent' items from other manufacturers.

Edited by DiRTgarage

ask JAGR33... he went from the T517z to the -5s... made slightly less peak power but more response and midrange... I've got T517z and they are borderline for a street setup... I like the way they come on as it feels fast, even if its not hehe

anyway go the garrets as they offer the best performance at the best price... I agree HKS are slightly better but also a lot more expensive with the exchange rate the way it is

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...