Jump to content
SAU Community

Jacking Up Ur Car

kikutaknight

By kikutaknight,
in WA Wasteland

 Share

Recommended Posts

kikutaknight Enthusiast

kikutaknight

Posted
Posted

I've seen pictures of people with their cars jacked up two wheels at a time with the jack somewhere in the middle...

also cars jacked up from somewhere other than that little bit on the side made for those dodgey little car jacks.

i've looked around on the bottom of my car but can't figure out exactly where people are putting these jacks. can anyone upload pictures or something for me? :D 

would be appreciated...zorz.

Link to comment
https://www.sau.com.au/forums/topic/289799-jacking-up-ur-car/
Share on other sites
260tech Proficient

260tech

Posted
Posted
I've seen pictures of people with their cars jacked up two wheels at a time with the jack somewhere in the middle...

also cars jacked up from somewhere other than that little bit on the side made for those dodgey little car jacks.

i've looked around on the bottom of my car but can't figure out exactly where people are putting these jacks. can anyone upload pictures or something for me? :P 

would be appreciated...zorz.

Check out this thread. http://www.ehow.com/video_4941952_put-jack...er-vehicle.html

Stay safe.

GW

Stinky Rooster Grand Master

Stinky Rooster

Posted
Posted

That vid misses quite a few vital safety aspects, like making sure the non-raised wheels are chocked properly for one...

Firstly, never ever ever try and use a sill jack on any other part of the car other than the proper jacking points. As Bard said, a road car is not strong enough to do this and you will either destroy the jack or your car. Heck, if your lucky, maybe even both!

If you want the front lifted then use the centre of the cross member - not the sump! Always use jack stands and try to keep them as close to the suspension pick up points as practicle as possible. The control arms used in that vid are a good idea, although I cant say using the edge of them is that bright. Personally I would use a bit of wood between the jack stand and the control arm (steel on steel is asking for trouble IMO) then you can use the whole control arm not just the edge.

For the rear, try putting the jack under the diff housing. Just be aware that the car will be VERY unstable as it is being jacked and can rock from side to side.

It should go without saying that safety should always come first. Never get under a car that is supported by a jack, always make sure the car is on level ground before raising it at all, and try to keep bystanders right the f**k away. One other person as a spotter is a good idea, but that should be it. Always fully chock any wheels that are to remain on the ground. Also, try not to open any doors on a car that is supported by a jack. Especially on 2 door cars, this can really upset the balance of the vehicle. Lastly, as I said before, its always a good idea to use wood between any steel jack or jack stands and the car. Apart from adding a "crush" factor that helps with stability, the friction coefficient is much higher making it more stable.

  • 3 weeks later...
  • 1 month later...
08yannch Rising Star

08yannch

Posted
Posted

+3 for the diff or x-member/rad support :laugh:

also i use the OEM jack on one of the sides so if a stand does fail the car wont fall all the way 2 the ground.

also never use bricks 2 suport a car i made that mistake once and i will never do that again :)

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

spare wheels and tyres are really good for getting a car up off the ground, if your doing something that doesnt require removing any of the wheels you can simply jack it up via the diff/xmember and chuck a spare wheel and tyre under each wheel, 2 if you need to go really high. if the wheels need to come off you can put the wheels and tyres under the chassis rails, make sure you have the car sitting on 4 points before you get under there and dont have the front supports too far back, the motor is the heaviest part.

08yannch Rising Star

08yannch

Posted
Posted

car ramps are good 4 doing work on a car when u don't need 2 take off the wheels and also there is no ramp solution 4 raising the whole car unless u make some.

4 me im restricted when it comes 2 space so im stuck with a trolly jack and axle stands (modified 4 skyline)

08yannch Rising Star

08yannch

Posted
Posted
with the height of the average skyline ramps would need to be about 8 feet long to be much good to ya

unless you remove the front bar or something????????

well all u do is wedge a thick bit of wood in there to extend the length

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Manur33
      Vag Coil Diy loom wire guage selection

      By Manur33 · Posted

      Can u check this way it works for power supply?
    • Manur33
      Vag Coil Diy loom wire guage selection

      By Manur33 · Posted

      These coils draw 10amps that what i read online
    • nouveau_poor
      Unknown sound similar to BOV on positive boost with partial throttle RB26

      By nouveau_poor · Posted

      I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      That worked out PERFECTLY! Thank you big time to JJ. He was able to swap me his stock diff. He drove all the way to me as well. Killer! Removal & install was pretty straightforward. The diff itself is HEAVY. So that’s a 2 man job.  Man does the car drive nice now! Couldn’t have worked out any better 👌
    • DannyDee2
      First time owner v35

      By DannyDee2 · Posted

      Welcome mate!
×
×
  • Create New...