Jump to content
SAU Community

Recommended Posts

I've seen pictures of people with their cars jacked up two wheels at a time with the jack somewhere in the middle...

also cars jacked up from somewhere other than that little bit on the side made for those dodgey little car jacks.

i've looked around on the bottom of my car but can't figure out exactly where people are putting these jacks. can anyone upload pictures or something for me? :D 

would be appreciated...zorz.

Link to comment
https://www.sau.com.au/forums/topic/289799-jacking-up-ur-car/
Share on other sites

I've seen pictures of people with their cars jacked up two wheels at a time with the jack somewhere in the middle...

also cars jacked up from somewhere other than that little bit on the side made for those dodgey little car jacks.

i've looked around on the bottom of my car but can't figure out exactly where people are putting these jacks. can anyone upload pictures or something for me? :P 

would be appreciated...zorz.

Check out this thread. http://www.ehow.com/video_4941952_put-jack...er-vehicle.html

Stay safe.

GW

That vid misses quite a few vital safety aspects, like making sure the non-raised wheels are chocked properly for one...

Firstly, never ever ever try and use a sill jack on any other part of the car other than the proper jacking points. As Bard said, a road car is not strong enough to do this and you will either destroy the jack or your car. Heck, if your lucky, maybe even both!

If you want the front lifted then use the centre of the cross member - not the sump! Always use jack stands and try to keep them as close to the suspension pick up points as practicle as possible. The control arms used in that vid are a good idea, although I cant say using the edge of them is that bright. Personally I would use a bit of wood between the jack stand and the control arm (steel on steel is asking for trouble IMO) then you can use the whole control arm not just the edge.

For the rear, try putting the jack under the diff housing. Just be aware that the car will be VERY unstable as it is being jacked and can rock from side to side.

It should go without saying that safety should always come first. Never get under a car that is supported by a jack, always make sure the car is on level ground before raising it at all, and try to keep bystanders right the f**k away. One other person as a spotter is a good idea, but that should be it. Always fully chock any wheels that are to remain on the ground. Also, try not to open any doors on a car that is supported by a jack. Especially on 2 door cars, this can really upset the balance of the vehicle. Lastly, as I said before, its always a good idea to use wood between any steel jack or jack stands and the car. Apart from adding a "crush" factor that helps with stability, the friction coefficient is much higher making it more stable.

  • 3 weeks later...
  • 1 month later...

+3 for the diff or x-member/rad support :laugh:

also i use the OEM jack on one of the sides so if a stand does fail the car wont fall all the way 2 the ground.

also never use bricks 2 suport a car i made that mistake once and i will never do that again :)

spare wheels and tyres are really good for getting a car up off the ground, if your doing something that doesnt require removing any of the wheels you can simply jack it up via the diff/xmember and chuck a spare wheel and tyre under each wheel, 2 if you need to go really high. if the wheels need to come off you can put the wheels and tyres under the chassis rails, make sure you have the car sitting on 4 points before you get under there and dont have the front supports too far back, the motor is the heaviest part.

car ramps are good 4 doing work on a car when u don't need 2 take off the wheels and also there is no ramp solution 4 raising the whole car unless u make some.

4 me im restricted when it comes 2 space so im stuck with a trolly jack and axle stands (modified 4 skyline)

with the height of the average skyline ramps would need to be about 8 feet long to be much good to ya

unless you remove the front bar or something????????

well all u do is wedge a thick bit of wood in there to extend the length



  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...