Jump to content
SAU Community

Recommended Posts

think it was me

i drive a stock gtr

you went up to the freeway

nice to be spotted :)

Yep up the F3 everyday for tailgating fun by red P platers :)

Car looks noice :P

Also spotted a white 33 (S2 wing) on the F3 last night between Wyong & ourimbah exits Southbond about 9.30pm lat night... couldn't quite catch up..just noticed the stove lights ;)

spotted wtf 33r last night i was in my mates forrester and u wouldnt run. soft hahaha

Yay my first Spotted!

Ah is that who it was! I was half asleep nor the mood, plus I'm not in a postision to lose my car and licence it means job gooooone! What was the poofy run against the TX3?

i spotted him on friday night at thornleigh maccas... i should have gone over and said hey but i was eating :P

I saw your car there too. should have come up! I dont bite ......................... (hard)

Yay my first Spotted!

Ah is that who it was! I was half asleep nor the mood, plus I'm not in a postision to lose my car and licence it means job gooooone! What was the poofy run against the TX3?

I saw your car there too. should have come up! I dont bite ......................... (hard)

shoulda... but i make an ass of myself enough without jumping into the middle of a group going "WHO OWNS THAT PIECE OF SHIT!?"

saw 2 skylines today... two that i feel like mentioning at least... both in chatswood...

one a silver 34... plates ** ** ** something... another a red 33... plates ******... the only reason im mentioning them is cause they flashed back :(

GET SOME MEMORABLE PLATES FFS! i dunno who the f**k you are :rolleyes:

Edited by DRD-00F

Saw 2 jillion Skylines last night on the way to Heaseman's Suspension, then another 1 million (and their owners, and, finally, another Stagea :):(:rolleyes:) while there, then quite a large number of Skylines today.

spotted a black 33 with buddy club stickers on the side, near the start of the harbour bridge last night at around 6pm (give or take 20 mins), heading towards the city. Pretty sweet

caps lock Mikey :rofl:

916

I spotted a white 33 on pac hwy series 2 with fmic around lindfield- looked standard other than that.

was in the 31 - hence why u didnt see me :mellow:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...