Jump to content
SAU Community

Recommended Posts

got a flash from a gunmetal grey r32 gtr with plates GTR-32P around lunchtime at rocky point rd sans souci, had SAU stickers too

Hey mate sorry abot late reply that was me :blink: thanks for spoting. I saw your tough beast with nice intercooler very nice! :P

I was on my way to doctors and to get some cobwebs out of my pipe.

See ya around are you local?

Dave

Spotted about 10 or so R33's today! Probably more but lost count lol

Black R34 GTR at George street with black lmgt4's tonight! Looked insane!

Another black R34 GTT no idea what road but it was just outside the city!

Yellow R34 GT at lidcombe behind me at the lights :ermm:

And R32 GTR with plates GT32TR or something on the lines of that :down: at The Rocks tonight, had LED rear lights.

Finally Spotted, you must of been out of work early yesterday?

Well kind of. I had to compile some reports and then present them in a teleconference at 11pm to the US. Sarked deek.

Did you get new rims?

Well kind of. I had to compile some reports and then present them in a teleconference at 11pm to the US. Sarked deek.

Did you get new rims?

Ah ok, ive had them for a while they were on there at the last cruise.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...