Jump to content
SAU Community

Recommended Posts

That might have been Elliot

From the 31 forums, Ravi? I haven't been on there in ages, but I do remember some mentioning of a few owners in and around this area.

saw a few today.

- gunmetal/dark grey r35 on james ruse drive at about 4.00 pm ish.

- yellow r34 coupe turning onto shaftsbury rd in burwood not long after

- white 4 door r34 not far behind the yellow one but it kept going down parra road

- r33 parked in hurlstone park near the pub

I just saw this now. Black r33 with big chromies?? Next to grumpys on the corner was me

From the 31 forums, Ravi? I haven't been on there in ages, but I do remember some mentioning of a few owners in and around this area.

Yep, white Passage with dished BBS wheels. He's around the Blacktown area

OT: Last week I spotted a silver BNR32 with meshies, low, on M4 around 10am heading eastbound. Think it was a Tuesday.

Also spotted a gunmetal BNR32 with dark TE37s in Artarmon, nice stance.

292848_10150303993446537_511696536_8219239_914751110_n.jpg

that was on kent st in the city yesterday and then this out near cronulla today,.

314868_10150303993616537_511696536_8219240_2090528890_n.jpg

and finally this slightly hideous R33 in surry hills the other night..anyone going to own up to it?

293346_10150296984846537_511696536_8177429_2073986235_n.jpg

Also spotted a gunmetal BNR32 with dark TE37s in Artarmon, nice stance.

Hey dude, that is def me.. where abouts in Artarmon was it?? live same suburb.

Next time stop and say ello!

They are fake TE37's :whistling: *Rota Grid-R*

saving the TE37's for my R34 Gtr when i buy one lol.

cheers man.

J

Grey R32 Gtst with what look like TE37's 17" white? Gtr bodykit and wing *sounds mean! Spotted Chatswood and Willoughby always pumping up Mowbray Rd watch for the RBT stations dude.

Bayside Blue R34 GTR vspec? BBS mesh wheels appropriately lowered. Mowbray rd and going past Artarmon station most mornings. (U were passing me on foot however now i have my car back hopefully will follow u down next time, Lovely machine)

Black R33 Gtr *5 Spoke wheels maybe LMGT4s?? Again Spotted Mowbray rd Artarmon going northish. hot ride dude.

R34 GTR Dark grey/Black Tidy setup ARC intercooler nicely lowered (I ran past you in Chatswood shopping centre carpark last night as you were coming up. I was with the white EVO TME, lol i was holding you up as my ticket was few minutes over and had to pay $5.)

Bayside Blue R34 GTR vspec? BBS mesh wheels appropriately lowered. Mowbray rd and going past Artarmon station most mornings. (U were passing me on foot however now i have my car back hopefully will follow u down next time, Lovely machine)

Black R33 Gtr *5 Spoke wheels maybe LMGT4s?? Again Spotted Mowbray rd Artarmon going northish. hot ride dude.

see both every morning on my walk to the station down mowbray :D small world :)

see both every morning on my walk to the station down mowbray :D small world :)

Crazy man! your near Mowbray. Probs walk straight past mine as well. Gunmetal R32 gtr on or there abouts and towards Station.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...