Jump to content
SAU Community

Recommended Posts

Looking to get some track rubber but unsure which tyre to get. At the moment it is between the AZENI and Dunlop Formula R road/race types.

Azeni are cheper but not so much that they rule out the Dunlops if they are a gripier tyre. Looking for quantative answers like lap times with road rubber then road/race rubber around tracks.

At the moment im doing 2.01 at Eastern Creek and 1min 15 at Wakefield on road rubber. For the approx $1000-1200 for road/race rubber will i get a 1, 2, 3 second improvement?

OR, should i use that money to chase more hp.

Also my car has a degree of adjustment in the suspension, castor, camber, sway bars etc, would it be a waste of time stiffening up swaybars??

Interested in peoples feedback

Link to comment
https://www.sau.com.au/forums/topic/2992-track-rubber/
Share on other sites

If you're looking for someone who had tried both AZENIS and Dunlop D01Js, you might be hard pressed to find such a person mate :P

I use Dunlop D01Js on the road on my rear tyres and they are grippy as all hell... Absolutely mind-blowing levels of grip once they're warmed up... Except they're pretty nasty in the wet...

I also have a set of D01Js (front and rear on R33 GTR rims) for the track, but I haven't had a chance to try them out yet... I'll hopefully be going down to Wakefield tomorrow to give them a thrash...

From all accounts, I hear that the D01Js are quite measureably better than AZENIS.

Link to comment
https://www.sau.com.au/forums/topic/2992-track-rubber/#findComment-52876
Share on other sites

Hi Roy,

I run Dunlop D01Js, on my second set (but cost me $1800 all up, dunno about getting em for $1200....)

They make a huge difference over my road Falkens:

Wakefield 1.16 -> 1.11

Eastern Creek 2.07 -> 2.00

Oran Park Short 57 -> 54

These are all times for a stock 33GTST

As mentioned below, you need to warm em up properly like any racing tyre - they really soften up as they get hot - almost got caught out a few times on first laps :uh-huh: I'm a huge fan of these - great value for these sort of improvements in times.

Best of all, theyre legal to drive to and from the track - full slicks (sicks?) may give a better improvement but too much trouble for me. Haven't tried Azenzis to compare.

My 2c is that suspension / tyre improvements are always the most rewarding place to start - going fast round corners is much more fun than fast down the straights......

Merli, you're brave to run them all the time, they are damn noisey and tramline like crazy (and they suck in the wet).

Link to comment
https://www.sau.com.au/forums/topic/2992-track-rubber/#findComment-53230
Share on other sites

Originally posted by Duncan

Merli, you're brave to run them all the time, they are damn noisey and tramline like crazy (and they suck in the wet).

I don't have any other choice...

My car is making 263.8kw @ wheels, so any other tyre is useless...

I just have to drive very very slowly in the wet, and make DAMN sure I don't hit boost...

Link to comment
https://www.sau.com.au/forums/topic/2992-track-rubber/#findComment-53726
Share on other sites

  • 2 months later...

I have to order the tyres im after by friday if i want to make the EC track day on 21/11.

Im down to Dunlops D01JS or Bridgestone RE540. Price is within $150 of one another so down to grip alone. (I now have to run 17s because of 330mm discs , 17"= more $$$)

A lot of Jap cars seem to use Nitto or Bridgestone RE540, but i cant find any compound info on either the RE540 or D01JS. I know the AZENI i was looking at is 200, compared to 230 of the Falken 451 i currently run. Tyre supplier THINKS the Bridgestones are about a 60.

Could anyone out there running either D01JS or RE540 do me a huge favour and check out the sidewalls for me and tell me the tyre compound. Cant find any info in English on the web.

Cheers race fans.

Link to comment
https://www.sau.com.au/forums/topic/2992-track-rubber/#findComment-91064
Share on other sites

Originally posted by Roy

I have to order the tyres im after by friday if i want to make the EC track day on 21/11.

Ring Gary's Motorsport Tyres in Blacktown.

URL: http://www.motorsportworld.com.au/outlets/garys/

Ph: 02 9676 8655

I bought 4x 235/45ZR17 Dunlop D01Js off them for $400 each. They supply those tyres for all the motorsport teams, so they have hundreds and HUNDREDS in stock in their shop.

No need to pre-order. I rang in the morning, and drove there that afternoon.

Link to comment
https://www.sau.com.au/forums/topic/2992-track-rubber/#findComment-91334
Share on other sites

Yeh, ive been speaking to Sean at Gary's Motorpsort Tyres, i need 215/45/17s on the front, a size they dont keep in stock. They are also very busy with the Bathurst weekend.

Oh if only i could get my hands on a used pair from the Bathurst weekend, i imagine there is a hell of a lot of wasted rubber from these events.

I think i may go with the Bridgestones anyway, see if anyone (Merli/Duncan) want to swap one day at a track and see if they are any better/worse then the Dunlops you guys are running. A lot of the Jap feature cars seem to use the RE540s, cant be that bad.

Link to comment
https://www.sau.com.au/forums/topic/2992-track-rubber/#findComment-91443
Share on other sites

HI there,

I have used both tyres on different cars, I don't have data as they are different cars ....however,

get the dunlop

get the dunlop

get the dunlop

They are so much better than azenis. They have a far higher level of grip when warm, they wear slightly quicker but are far superior on the limit too. Azenis are not really a race tyre, they were not good enough for race thats why they are available more as a road tyre, but they are useless as a road tyre as they never get warm unless you do a really hard run for 10km plus...ie up reefton spur for those of you in melbourne...and when they are cold they are less grippy than a normal good qualkity road tyre. They do however have a nice stiff sidewall and are predictable.

Cheers,

Russ

Link to comment
https://www.sau.com.au/forums/topic/2992-track-rubber/#findComment-91782
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...