Jump to content
SAU Community

Recommended Posts

yeh, ill be making an appearance at the museum this friday as posted on the museum thread.. poker nite was at jerra club, they have it every monday nite.. thursday nites at roos club in qbn..

Tuesday nites at the Tigers club qbyn.

Canberra cant conform ATM.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/318/#findComment-2390750
Share on other sites

That would have been me going to pick up the girlfriend :D sorry i didnt see you. I was sitting behind a evo 8 most of the way

Spotted a black R33 going along the parkway towards woden about 4:45. I was ging the other way... Didn't get time to give a wave because I only just noticed it as it was going by.
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/318/#findComment-2395740
Share on other sites

spotted a nice sounding dark blue R31 going over Hindmarsh tonight at about midnight.

Do you know if it had chrome rims or white rims??? There "was" a stolen blue r31 with white rims(dirty when i saw it last) with no center caps, r31skylineclub sticker on the rear drivers window and a handsized paint chip on the front quater. The cops called me today and told me they found it. I did see the thieves but a 2nd statement would be heaps better, if you saw anyone???

Anyways, feel free to pm me and i'll give you the case number to give a statement, if you want.

And if it had chrome 19inch rims then don't worry... his car ain't stolen yet...

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/318/#findComment-2399129
Share on other sites

oh.. sorry to hear, was it your car that was stolen?

I couldn't see much sorry!!... it was really dark and we were going up the hill on Hindmarsh where there's no streetlights or anything...I just came up behind him and then went into the middle lane and passed him.

I didn't even see the rims properly :P but thinking back I reckon there might have been a flash of bling when I went past so maybe it was the other guy.. I think he might have been alone in the car too - the stolen one would have had at least 2 guys in it??

Where did the cops find it?

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/318/#findComment-2400405
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...