Jump to content
SAU Community

Recommended Posts

lol first spot in months mind you its been off the road for a month and will be till i can get the A/F ratio down. Yeah its been ages you have only just seen me do a drive by with carbon bonnet ill bring it to Beaus

Yah.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/338/#findComment-2550681
Share on other sites

lol first spot in months mind you its been off the road for a month and will be till i can get the A/F ratio down. Yeah its been ages you have only just seen me do a drive by with carbon bonnet ill bring it to Beaus

Yah.

Well I'm proud I spotted it! I did think of you when i saw it but im like na cant be shauns!! you better! been a while!

Edited by skyline_babe5
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/338/#findComment-2550691
Share on other sites

spotted some guys driving on Copeland Drive.. I think it was on sunday (??), maybe going on a cruise or something.. there was an R33 first with a cf bonnet and then about 5 other cars... rex, silvias n others..

i just waved at everyone lol

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/338/#findComment-2551272
Share on other sites

spotted the silver R33 GTR with carbon bonnet again last night in civic. has a sunroof. definately has had some sort of work done to the rear guards as they were both bogged up/prepped for painting. sounded tough

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/338/#findComment-2552296
Share on other sites

I spotted a silver R33 with a carbon fibre bonnet heading into Weston Creek about an hour ago. I wasn't sure if it was a GT-R, it had widened rear guards, but they were in primer.....

if it was the one with the fake GTR badge, it might be the one that was @ Inline, an asian guy owns it, and i think its around the 300rwkw mark with a GT3540.. not too sure though..

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/338/#findComment-2554536
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ha, I've never pressed the X in all these years incase it removed the notification for all Admins
    • I don't know, I've never done it that way, but 1. While it is an interference engine, there is still clearance between the valves and the piston at all points in the regular timing cycle 2. There is not a lot of distance before you can't catch the top of the valve stem any more I don't know if 2 is greater or less than 1. But 3. If it doesn't work out you are f**ked, engine is coming out to disassemble so it is a big bet.
    • Semi slicks are horrible for road use, just use a high performance road tyre unless you really need the maximum grip. Noisy, unpredictable (amazing, until they are not), expensive due to very high wear and not good in cold and particular wet. And yes, it is a thing to store cars on stands instead of tyres if you know they are going to be parked up long term.....but who ever realises that a short park is going to stretch into years before it is out again!
    • I know in Australia you'll definitely get above 30c. Parked in the shade in Summer you'll be above that. 😛 But in cooler climates, you might get that warm driving on the highway for a bit, but you'd never get to full heat temp. I'll try and find some of my historical tyre temps between Aus summer and winter (be aware immin the warmer area of Aus too.)
    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
×
×
  • Create New...