Jump to content
SAU Community

Recommended Posts

Had a run along the parkway with a white R34. Pretty sure the driver is on here, just cant remember your name. Car looked awesome, especially with those eyelids. just a shame you had to see mine in its current totally-dirty state!

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/359/#findComment-2727957
Share on other sites

Had a run along the parkway with a white R34. Pretty sure the driver is on here, just cant remember your name. Car looked awesome, especially with those eyelids. just a shame you had to see mine in its current totally-dirty state!

Thanks mate. Was admiring the dish on your rear wheels, will have to get me some new wheels some day!

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/359/#findComment-2728007
Share on other sites

Wow, must be alot of skyline owners in weston area.

I was at weston car wash last night at around 9:30pm and there was a R31 next to me. Mark I think it was. Hope you had good luck with the rego.

also just spotted another red R31 on athollon just then with a big R31 skyline australia sticker on the window.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/359/#findComment-2732763
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...