Jump to content
SAU Community

Recommended Posts

lol yes it does. Ultimate tunes guys have gone on a holiday for 10 days to tassy so il get the work done in jan some time. But no sin i have NOT picked up the injectors or a new boost controller yet. Still looking around. Can't wait till its tuned and off the run in stage...

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/789/#findComment-6674947
Share on other sites

LOL there's no such thing as DONE no matter how hard you try to tell yourself.

I have been telling myself this for the past year.

Ohh just a turbo and tune and I will be fine.

Now I have a water meth kit to be installed.

Already purchased coilovers and new rims since then.

Now looking at a new radiator, intercooler and exhaust.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/789/#findComment-6674975
Share on other sites

Now I have a water meth kit to be installed.

Already purchased coilovers and new rims since then.

What rims did you get kasko?

Also, it'll be a big moment when the chick from the orange skyline finally waves back. I wonder who will get the privilege!

Edited by Mitcho_7
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/789/#findComment-6675065
Share on other sites

LOL!

Famous last words

under the bonnet... there is nothing left for me to do. apart from like go a big single etc but ill never do that. i bought a GTR for a reason. I mean i could stroke it but again thats something ill never do. Apart from that... its all been done haha

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/789/#findComment-6675073
Share on other sites

those are pretty nice, grats. You going for the bat mobile black on black look huh

Yep :D

Was going to do matte black but after looking at it I like the way it is now.

Maybe a tad more low at the front.

But my exhaust is sooooo close to the ground.

Hence the new exhaust

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/789/#findComment-6675130
Share on other sites

Who rolled your guards for you?

I like the black on black, looks the goods.

I did it myself haha

Ended up buying a heat gun + rubber mallet and went to town on them. Worked out great!

Cracked the paint trying to use a bar and no heat gun but that was before I got the other stuff

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/789/#findComment-6675879
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...