Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Spotted black r33 (looked like GTS-t) in O'Connor roundabout pulled off at side of the road, looked like a red hatchback had run up the back of him and they were exchanging insurance details.

Hope nobody was hurt ! (didn't look to serious, but you never know).

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/658/#findComment-5709096
Share on other sites

Spotted a GROSS Baby sh!t Browny Greenish Matte finish S14 200sx with silverish front bar & stock rims, at Jammo this morning. Blaaarrrgh!!! Nearly tossed my cookies.:sick:

I really hope that is about to be Re-sprayed.:yucky:

If Not... Shame on you!!!

Edited by Not a Pulsar
Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/658/#findComment-5711829
Share on other sites

Spotted a GROSS Baby sh!t Browny Greenish Matte finish S14 200sx with silverish front bar & stock rims, at Jammo this morning. Blaaarrrgh!!! Nearly tossed my cookies.:sick:

I really hope that is about to be Re-sprayed.:yucky:

If Not... Shame on you!!!

Bwahaha lolz!! :rofl2:

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/658/#findComment-5713396
Share on other sites

Spotted Miranda getting into her s14 after work :ninja:

Also spotted Gus driving out of the HyperD underground carpark, didn't recognise the wheels (including the one on the back seat). I was the dude on the pushy waiting to go around you.

Link to comment
https://www.sau.com.au/forums/topic/30059-spotted/page/658/#findComment-5729013
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...