Jump to content
SAU Community

Recommended Posts

honestly I would probably rate the old a048s over the 888s with one downside that the a048 does go off after fewer heat cycles, but it's outright pace is better than the 888. the new A050 is miles better though.

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

595RSR is priced between r-comps and streets, and it sits where all the other street cross track tyres sit in terms of price and performance.

KU36 can't be beat for the price but I don't understand when people say stuff like "If I'm paying double the price of KU36 for X or Y tyre then they better be double the performance!" There's not much that I can think of when talking about performance, where you get double the goodness for double the price - it doesn't work that way unfortunately.

honestly I would probably rate the old a048s over the 888s with one downside that the a048 does go off after fewer heat cycles, but it's outright pace is better than the 888. the new A050 is miles better though.

It's the heat cycling that rates them lower for me. They are fine at the start of their life but rubbish after a few days where as the r888 is slower but more consistent for it's life.

Yeah, all the a050 feedback i've seen is positive.

for what it's worth, if you are even half serious you are wasting your time with anything but the best tyres.

when you are on the track are you competing (eg supersprint)? or running a lap timer?

top line semi slicks like re55s or dz03 will give you at least 1 second a lap over falken rsr/kumho ku36. second tier semis like kumho v70 or toyo 888 or yoko a048 will be at least 1/2 sec faster.

If cost is an issue (it always is lol) the v70 kumhos are a good choice at about 1300 va set in 245/40/17.

even better if you want to save money - run the smallest diameter wheel you can fit over the brakes. 17s are about 30% cheaper than 18s and 16s are cheaper again. the stiffer sidewall of semi slick tyres minimises or eliminates any disadvantage from the higher sidewall.

Dunc - since you menetioned v70s where do you get them from? FR sport? and how did you rate the khumo slicks you were on at OP?

MRA gives the option of slicks or treaded so depending on price id prefer the slicks.

you can pm me if you want

yeah talk to John at F-sport. Tell him I sent you and he will add 10% to the price lol. At 1300 a set they are half the price of dunlops in the same size, so if 1/2 sec doesn't matter for what you are doing they are a bargain.

At Oran Park I had kumho slicks on the front and falken slicks on the rear (same size). They were f**king excellent. For example I was taking Suttons in 4th which i have never even considered on semis. Literally 10-20% faster in a corner so 1-2sec for a whole lap.

When slicks are an option they can be cheaper too because they might last longer (up front cost may be say 20% higher but if they keep their performance 50% longer....). But you would still need either semis for bad weather or be willing to park it...makes for a difficult decision because everyone I know who has wet tyres never uses the things which makes slicks an expensive option.

slicks worked well for me because I normally have to use semis, so I had a few I could drag along in case it rained (which it didn't in this case, despite the forecast)

The rain issue has me a bit doubtfull, as i only have 1 set of rims atm, I dare say I would park it in the wet, unless i buy a cheap set of factory rims and throw some KU36's on them for wet days / practice days

teh slicks should put me (in theory) in the 1:08s easily at wakefield which is right up the front of the current MRA field so for a bit more money it might just be worth it.

yeah...also if it is only a single race meet then slicks aren't such a big gamble.

with stuff like the state champs though you need to score well every round, so you just can't risk having to sit out a whole round from a points persepective

How do the V70's compare to the RE55's?
....top line semi slicks like re55s or dz03 will give you at least 1 second a lap over falken rsr/kumho ku36. second tier semis like kumho v70 or toyo 888 or yoko a048 will be at least 1/2 sec faster.....

my opinion only....but i have seen them compared in very similar circumstances

595RSR is priced between r-comps and streets, and it sits where all the other street cross track tyres sit in terms of price and performance.

KU36 can't be beat for the price but I don't understand when people say stuff like "If I'm paying double the price of KU36 for X or Y tyre then they better be double the performance!" There's not much that I can think of when talking about performance, where you get double the goodness for double the price - it doesn't work that way unfortunately.

last time I priced Federals they were almost exactly the same as what I got quoted for Toyo R888 and RE55S. Up around $330 per tyre in 235/45*17

You can get tyres that perform almost exactly the same as the RSR for almost exactly half the money.

OR you can get tyres for exactly the same money as the RSR that will run rings around them.

understand?

You're shopping at the wrong place Harry. any time you want feddy's in the rsr guise let me know.

The feddy's are not the best semi on the market, Nor do they claim to be.

they do offer outstanding value for money for those looking for one tyre to do it all. They are a competent track tyre and an outstanding street tyre for a high performance ride. The Khumo's are probably similar but from what i have seen the feddy will go a lot further than the khumo.

I've run sub minute on qr sprint using the rsr and still get good mileage from them on a daily usage deal.

The best they are not. The best value they most certainly are IMO.

last time I priced Federals they were almost exactly the same as what I got quoted for Toyo R888 and RE55S. Up around $330 per tyre in 235/45*17

Where from? Most of the prices I've seen for 17" RE55S have been at least $400 each (RRP is over $538). If I could get them for $330 each I'd be pretty stoked.

last time I priced Federals they were almost exactly the same as what I got quoted for Toyo R888 and RE55S. Up around $330 per tyre in 235/45*17

You can get tyres that perform almost exactly the same as the RSR for almost exactly half the money.

OR you can get tyres for exactly the same money as the RSR that will run rings around them.

understand?

You're paying too much for RSRs.

Those R888's are grey imported, try price the proper current australian stock australian compounds.

RE55S in 235/45/17 for $330each? No chance, not even close.

You need to do a bit more homework :)

Edited by _Wing_
for what it's worth, if you are even half serious you are wasting your time with anything but the best tyres.

when you are on the track are you competing (eg supersprint)? or running a lap timer?

top line semi slicks like re55s or dz03 will give you at least 1 second a lap over falken rsr/kumho ku36. second tier semis like kumho v70 or toyo 888 or yoko a048 will be at least 1/2 sec faster.

If cost is an issue (it always is lol) the v70 kumhos are a good choice at about 1300 va set in 245/40/17.

even better if you want to save money - run the smallest diameter wheel you can fit over the brakes. 17s are about 30% cheaper than 18s and 16s are cheaper again. the stiffer sidewall of semi slick tyres minimises or eliminates any disadvantage from the higher sidewall.

It's for supersprinting. Went cheap ones because there's still a few more parts that I need to get relatively soon. I would have liked to gave gone the RE55's but the rears alone were about $500 (for 255/40/17). Next time it comes to upgrade I'll fork out for proper semi's.

With what you were saying with the RE55's and 888's; one of the guys in the wrx club tested both of them back to back at EC. The RE55's were just over a bit over a second a lap quicker.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...