Jump to content
SAU Community

Recommended Posts

Hi Guys,

Changed the stock turbo on my rb20 yesterday for a s2 rb25 one and it wont make any boost at all.

Drives fine off boost and as soon as you get into positive pressure its shudders really bad and wont go past 0.

Car is also Idling abit high (intercooler piping leak?) but this shouldnt cause it to not build boost?

Any help would be muchly appreciated!

Did you leave a rag in the intercooler pipe work???

It's allright... everyone dose it.

No rags in the piping lol. Any other ideas of what It could be?

What about the nipple for the actuator? I drilled and tapped it into the elbow this should be fine yeah?

Not really looking forward to pulling It all apart again lol :)

by any chance you did spin the shaft and stuff making sure both sides of it spin right lol, like u havent shit an exhaust wheel without knowing it have you haha

other than that look for big leaks, but somehow i doubt it.. based on the offboost drivability i mean

Car is also Idling abit high (intercooler piping leak?) but this shouldnt cause it to not build boost?

Are you saying that you suspect an intercooler pipe leak, but that an intercooler pipe leak wont stop the car building boost? Because it will - the boost will leak out!

Are you getting black smoke out the back? If you have a boost leak it will run very rich and you'll get black smoke. Perhaps so rich that missfires/shudders.

If its not a boost leak check that the wastegate isnt stuck open (you should be able to move the actuator rod with your hand, or just apply 10psi air pressure to it and watch it move). But i dont think your symptoms match a stuck wastegate.

Are you saying that you suspect an intercooler pipe leak, but that an intercooler pipe leak wont stop the car building boost? Because it will - the boost will leak out!

Are you getting black smoke out the back? If you have a boost leak it will run very rich and you'll get black smoke. Perhaps so rich that missfires/shudders.

If its not a boost leak check that the wastegate isnt stuck open (you should be able to move the actuator rod with your hand, or just apply 10psi air pressure to it and watch it move). But i dont think your symptoms match a stuck wastegate.

Thanks for the help MrKotter, I did get abit of black smoke out the exhaust when I first started it and it did feel like it was missfiring but really violently much more so than when my coilpacks died.

And I cant seem to move the actuator rod at all but the flap is closed not open?

Thanks again for your help mate!

Oh and also to everyone else, yes the exhaust wheel is still there and spins freely

Thanks for the help MrKotter, I did get abit of black smoke out the exhaust when I first started it and it did feel like it was missfiring but really violently much more so than when my coilpacks died.

And I cant seem to move the actuator rod at all but the flap is closed not open?

It will be very stuff to move by hand, maybe too stiff. And the actuator pushes on it to open the WG, so you need to try to move it in the same direction. But yeah, its almost certainly not stuck open if you're using the stock dump, and if it was you probably wouldnt be able to move it by hand anyway......so keep looking for the leak. Are you sure your new boost nipple is airtight?

Thanks for the help MrKotter, I did get abit of black smoke out the exhaust when I first started it and it did feel like it was missfiring but really violently much more so than when my coilpacks died.

A boost leak is a much more violent miss fire and cut, as the car is reading that it has 3 times as much air going in as really is, so it throws in 3 times as much fuel as needed, affectively flooding the motor.

A boost leak is a much more violent miss fire and cut, as the car is reading that it has 3 times as much air going in as really is, so it throws in 3 times as much fuel as needed, affectively flooding the motor.

Cheers guys, looks like I'm definately looking for a boost leak then, thanks for the help everyone.

Will report back once fixed.

Hi Guys,

So I took everything apart and put it all back together again, started her up and she seemed fine idle better than last time and much lower too (bout 900).

took it for a drive up the street and when I stopped at the intersection and put it in neutral the car revved by it self upto about 5-6k almost like the throttle was stuck open?

popped bonnet and checked throttle cable and it seemed to be fine, so I started it back up again and managed to put it into gear and it stopped freerevving and I babied it home.

WTF is going on? more boost leaks? didnt get it up to temp so I havent tried to get boost yet.

Thanks guys, this is driving me crazy :)

edit: Just started it up again in the garage and its idling really high again, whats the best way to find the boost leak? soapy water around the silicon bends?

Edited by Jden

Manifold leaking? The problem is after the throttle body I would say, a gasket probably need to be replaced. You can try spraying around the area with carb cleaner to find the leak.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...