Jump to content
SAU Community

Recommended Posts

If i could load Nistune onto it and hook it up to my ecu, could do map changes on the fly. Eat your heart out powerfc hand controller :P

... or you could probe the ECU's input/output signals and just make it do what the ECU does via emulation.

your car's ECU is the PC equivalent of a 386. ARM processors can do 1000 times the calculations that your ECU can do in the same time.

... or you could probe the ECU's input/output signals and just make it do what the ECU does via emulation.

your car's ECU is the PC equivalent of a 386. ARM processors can do 1000 times the calculations that your ECU can do in the same time.

haha sounds like too much work.

Id be happy with map switching :P

Not sure nistune would run on windows CE though..

Removed the wing a gave my 33 a polish was quite chuffed with it really. A bit un-decided about the 'No-Wing"

SDC10518.jpg

SDC10515.jpg

SDC10514.jpg

SDC10513.jpg

gave the headlights a polish as well to get rid of the brown/orange tinge and the results were amazing

SDC10516.jpg

boo time for work :D

water pump, Gates timing belt, idler/tensioner bearing, cam seals, crank seal, fuel filter, thermostat, bearing stud/bolt kit - Thanks Kudos Motorsport

adjustable cam gears - Access Autoworks

and possibly a 52mm allum radiator from ISC

Damn you 200,000km service :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...