Jump to content
SAU Community

Recommended Posts

eqn.png

Yikes it's been ages since I've done any of this stuff. Must be some identity to simplify it. Just had a flick through my textbook, couldn't find anything too helpful :\

any of you cunce going to Armin for NYE?

Yes. Pumped.

any of you cunce going to Armin for NYE?

I wanted to go, but too many people i know dragging their feet.

off to ocean grove now instead, and a heap of mates are in Jan Juc, so going to have a uber massive NYE party down that way

haha first time in 12 years I won't own a skyline, and the nationals comes to VIC that's actually somewhat close to home. FFFUUU.

will have to rock out with my cock out with the S30 instead.

I wanted to go, but too many people i know dragging their feet.

off to ocean grove now instead, and a heap of mates are in Jan Juc, so going to have a uber massive NYE party down that way

Ill be in Ocean Grove too, thats where our beach house is :P

  • Nope 1

Shan, do you know any good placed to get my power steering rack reconditioned in dandy?

Mine was rebuilt through Revzone in Ringwood. Obviously they didnt do it, but had contact which did it cheaper than any steering rack mob I called from the yellow pages.

Give Revzone a call on 98700540 and let them know that Patrick (r32 gtst) had his steering rack rebuilt at your place. They'll point you in the right direction.

  • Like 1

Shan do u know where I can find a secondhand steering rack...anywhere? :P

2 days till tow truck! Getting the pig up our epic driveway will be a task and a half with no steering...

I know a place in Bayswater where you can exchange your steering rack for a reconed one.

asked them about mine but they seemed to only have 33/34 racks.

Mine was rebuilt through Revzone in Ringwood. Obviously they didnt do it, but had contact which did it cheaper than any steering rack mob I called from the yellow pages.

Give Revzone a call on 98700540 and let them know that Patrick (r32 gtst) had his steering rack rebuilt at your place. They'll point you in the right direction.

Cheers will do that tomorrow.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...