Jump to content
SAU Community

Recommended Posts

Even Paul walker was poking fun at chromies and spinners.

Also, that C10 GTR :O

Twas nice, was not expecting to see an old school gtr thats for sure

Where's this one supposed to fit in with the others?

Wasn't one of them a prequel?

Think the beginning of 5 is the end of 3 or something like that. Was confused i've only seen 1 and 2 had to get my mate to fill me in throughout. Oh and Keep watching after the credits are finished...

Bit early in the morning for you?

I never said he body wasn't tight - just her funbags, which will look like half eaten bags of rice when unleashed

Bit early? :P I pretty much don't sleep lol.

I agree, in that pic it looks that way, but in the movie you'll see it's not the case :) She's also a bit flatter than that I think.

Birds, do you still have plans for tonight? Gathering at mine if you're keen (same goes to anyone else, except mohsen)

Bit undecided on plans at the moment cause I was supposed to head down to PI, but my lift changed our plans and left yesterday which I couldn't make. Weighing up if I cbf driving down alone...will msg ya later on.

So my water pump is leaking coolant, got home and within 5 min there was a puddle...

Should I replace just the water pump or go all out, N1 water pump, trust/greddy timing belt, HKS cam gears???

Suppose depends how much you wanna spend and future plans..

,

Other news drjays rocks!

So my water pump is leaking coolant, got home and within 5 min there was a puddle...

Should I replace just the water pump or go all out, N1 water pump, trust/greddy timing belt, HKS cam gears???

Depends if you need your 100k service or not, or else I'd just do the pump. Read somewhere that cam gears on RB25 don't do much compared to 26

And yeah, I went to racepace for them to do the work - I got parts from Kudos (cheapest and tomei cam gears ftw.)

Cam gears

Bearings & seals

Belt

Water pump (just went stock one)

Fuel filter

And then they had to replace rear rotors and pads and they fixed a few other things up replaced oil on everything.. got a invoice somewhere be prepared to have a little more spare if your going in for a service but looking at 1k ish for just the engine stuff.. everything has to come out.

My invoice was 2k, but that was everything down to the windscreen blades, and slotted rotors / race pads obviously racepace are a bit more pricey than some places but they sure do know what they are doing. And local for me.

Going to Trent for my tune though, bit cheaper and considering he is JUST primarily a tuner and only heard good things I believe the car will be in good hands.

Forgot to mention, Chris at racepace called me often for updates which was great - rather than just doing the work and hitting you with the bill afterwards and didn't mind talking about options over the phone.

Edit: I went HKS cam gears at first but after talking to tuners apparently not the best because they only have 3 bolts and can possibly come lose and there goes your engine, whereas Tomei have 5 bolts - go the Tomeis.

A fellow connoisseur, Im impressed.

The sag is evident by the shoulder to approx nipple distance it's far to low to qualify for perkyness. Ask any man, any real man he'll tell you

I didn't wanna have to do this, but you cunts leave me with no choice.

Shay Laren. End of discussion

That's an arm and leg if it's labour cost... Jebus!

Haha went all out! I ordered 3 hats mid last week, should be here hopefully Wednesday ;)

What kinda hats you boys talking? 59fifty? if so where from and how much you paying?

You're assuming they'll sag without having seen them out of a top/bra...Shay Laren has her well and truly covered for size, and I wouldn't say they're hanging at her knees..

That and the fact the rest of her is amazing, there's no point wasting time talking about some other chicks cans you haven't seen..

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...