Jump to content
SAU Community

Recommended Posts

Get rid of existing and get braided from the turbo to the block. Personally I would get something custom made from somewhere like Enzed (well actually I make my own lines using Speedflow gear, but I assume you're not game to try that?). But plenty of people on here seem to be using the Kando lines with no problems.

FYI both 6262 and 6266 are rated as 700HP items. I'd be chasing that 66 CEA item, better tech is where its at.

The 6262 is 700hp and 6266 is 735hp.

Don't be fooled by the CEA crap, the wheel sizes have an influence over response, and the 6262 is more responsive.

It might be that the 62mm wheel is more responsive, but by how much? You can see that the CEA wheel has better blade design and would be an overall lighter rotating assembly. Im also confident the 66mm wheel would flow a metric shit load more.

If you were going 3L down the track I can see that the 66 mil would make for an intensely fast car.. but yeah I can accept 4mm in turbine exducer isn't anything to scoff at.

Thanks hanaldo, I will look at the lines a bit, sorry for the spam on the Precision thread but did you end up re-tuning your G3 again/ killawasps?

Edited by rondofj

On my car I have had a 6265, 6765,6766 and 7175. I have witnessed a 150rpm difference between a 6262 and 6265, hardly noticable, but there was also a couple of hundred revs between the 65 and 66 turbine wheels on my own car.

Yes it picked up 30hp atw but the point I was trying to make was, PTE marketed the same if not better response between the CEA wheel replacement wheels of the 65. Maybe that is the case with identical sized wheels, but from my experience not a bigger CEA vs smaller wheel. You can physically see the difference in the thickness of the older wheels.

On my car I have had a 6265, 6765,6766 and 7175. I have witnessed a 150rpm difference between a 6262 and 6265, hardly noticable, but there was also a couple of hundred revs between the 65 and 66 turbine wheels on my own car.

Yes it picked up 30hp atw but the point I was trying to make was, PTE marketed the same if not better response between the CEA wheel replacement wheels of the 65. Maybe that is the case with identical sized wheels, but from my experience not a bigger CEA vs smaller wheel. You can physically see the difference in the thickness of the older wheels.

It's funny that a 3 mm larger wheel with a 62 mm front was only 150 but 1 extra mm on a 67 was alot more noticable. Hmm.

got to remember that its 1mm on the exducer but they dont tell us what they have changed on the inducer. Could be a way larger wheel in a smaller trim... or could be a smaller wheel in a larger trim. Who knows..

PJ did you ever dismantle yours to measure the inducer on the turbine side? I have always wondered why PT dont farking advertise those figures. With the smaller stuff I had a feeling they kept it to themselves because the numbers would match up to older tech T3/T4 based things. Bad for business when your marketing 'new tech'. Obviously we know overall measurements are not the be all and end all, but it would certainly raise the question.

Yes we did, and you could be onto something there :whistling: either way they worked and worked well!

It would be interesting to back to back a CEA of the same size, but after spending 10 grand of my own money on Precision turbo's, I might leave it for one of you boys to step up :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...